Models > LSQ9659PW3

LSQ9659PW3 Whirlpool Washer - Overview

Get Parts and Repair Help for LSQ9659PW3

If you know the washer repair part you need, you can browse the list of all parts on the LSQ9659PW3, or you can search by name or part description. You can also find your part by where it is located on the LSQ9659PW3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LSQ9659PW3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.32

Agitator Directional Cogs

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

$11.77

Direct Drive Motor Coupling

This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.

$29.84

Direct Drive Water Pump

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

$2.52

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

$28.77

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity wash...

$8.07

Agitator Cam Kit

This kit included the cam, 4 dogs and bearing.

$21.75

Lid Switch

The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the grounding wire.

$2.18

Inner Cap Seal

Also known as an O-Ring.

$4.46

Agitator Bolt

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$3.76

Agitator Cap Barrier with Seal

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer wouldn't agitate

  • Customer: mike from Kent WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 486 of 492 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing usin... read more

No movement from Basket & agitator

  • Customer: Jeff from Wayne NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 473 of 502 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

Water pump leaking when machine used.

  • Customer: Tom from Granby MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 404 of 420 people found this instruction helpful
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary access to the pump. ... read more