Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LSD2615HEW > Instructions

LSD2615HEW Admiral Refrigerator - Instructions

All installation instructions for LSD2615HEW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LSD2615HEW
76-90 of 710
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Needed to replace a broken light switch

  • Customer: Ethan from Fort Collins, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 11 people found this instruction helpful
Popping out the broken switch was easy once I was able to see how the new switch part was engineered. The switch was made to be replaced, having a simple tension hook on the bottom of the switch which needed to be depressed to pull the switch out of the cabinet. Once pulled out, there were modular plugs for the power line that were easy to pull off the broken switch and plug into the new switch. Pop the new switch back in and VOILA, the lights worked again! Thanks to part select's good diagrams of the actual model of my refrigerator, it was very easy to hone in on the exact part I needed. I did notice one problem with the order as the correct series for the part was displayed earlier in the process, but had the wrong series later in the process. However,. I trusted the system and the part is for the right series and fit well (an exact match, down to the color). Thanks Part Select, I would definitely use you again.

I put my frig. outside on my deck during a kitchen remodel and when I brought it back in a hooked up the water line again, I solenoid fill valve on the back of the unit leaked badly. I found a big crack in it and guessed it must have had a bit of water left in it when put outside in sub freezing, w

  • Customer: Jonathan from Plymouth, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 7 of 8 people found this instruction helpful
I searched in line for a replacement fill valve and easily found it on your site w/ excellent diagrams. I turned off the frig., & the part came out simply and logically first removing the 5 screws that hold it in w/ a nut driver. Then remove the supply water line and the other quick connect lines that feed the ice maker and the chilled water dispenser. Then, disconnect the two wire harnesses that clip off easily by hand. They feed the two relays in the valve and are color coded. Remove the valve and reverse the procedure to hook it back up. Note: a little water will come out of the lines so be ready w/ a small bowl and a dish towel. After installing the new part, it was necessary to "bleed" the water lines of air by drawing a few glasses of water from the water dispenser to get the system operating normally again. One tool, common sense, 30 minutes. Probably saved $150 + on a repair man plus parts markup. Thanks very much!!

Refrigerator wouldn't cool

  • Customer: Fidel from Forest, MS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 12 people found this instruction helpful
First I removed the six screws from the cover. I then disconnected the two wires and pulled the small motor out with its base and removed two screws that hold it in place. I then changed the old one for the new one and set it back in its place. I then set the cover back and turned it on. I was happy again.

the helix end cap broke and the ice maker wouldn't dispence ice

  • Customer: jeff from brownsburg, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 15 people found this instruction helpful
Well it was very simple. I just pulled out the ice cube bucket , removed a few screws from the front of the bucket, pulled the front panel off, replaced the helix end cap too the auger, put all of it back together into a new ice bucket, screwed the front panel back on , than lined up the auger to line up with motor shaft of the freezer motor and what do you know I HAD ICE. My family was happy and i did this for under thirty dollars. A repairman would of cost more than three times that just to look at problem and would of cost more for the parts and the second trip to fix it. Thanks you for making it easy to find the part and for the quick delivery of the parts.

No ice

  • Customer: Jon from Boise, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 12 people found this instruction helpful
1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

Broken cup water fill on ice maker

  • Customer: Matthew from Aurora, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 9 people found this instruction helpful
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

My icemaker started leaking water into the catch basin and turning my ice into one big ice burg.

  • Customer: gary from carleton, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 6 of 6 people found this instruction helpful
Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

Not freezing or keeping thing cold in fridge

  • Customer: BRUCE from AMMON, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 9 people found this instruction helpful
Once I got the right part the repair was quick and easy. All I had to do is get the old part off with a screwdriver and curved needle nose pliers and the old part came right off. The new part went in just as easy. Quick and easy. Less than 15 minutes.

broken light switch

  • Customer: Richard from West Warwick, RI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 10 people found this instruction helpful
followed the instructions provided and that's it!

refrigerator made noise, smelt hot

  • Customer: Terry from Pittsfield, NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 10 people found this instruction helpful
While investigating problem (at 11:30PM of course) I saw the overload burst into flames. Problem Identified! Easily found and ordered part. Next day delivery. Exact same part easily plugged in. Total refrigerator down time was less than 40 hrs.

Thanks,
Terry

Fridge random humming

  • Customer: robert from central point, OR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 7 of 10 people found this instruction helpful
Unscrewed back of fridge and unplugged relay from compressor and plugged in the new one remember that the new one turns 180 degrees from existing switch.

Icemaker would not fill with water.

  • Customer: Linford from Cedarville, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 10 people found this instruction helpful
Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

Ice maker door broke allowing open hole to freezer

  • Customer: Clifford from Madison, IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 6 of 8 people found this instruction helpful
The ice maker panel on the freezer door detaches by removing two screens at the bottom of the panel behind the drip tray. My son held the panel while I removed three screws holding the ice chute cover. The ice chute door is attached to a spring loaded bracket. I only needed the actual door, but it was just as easy to replace the insulation and the seal. The seal was starting to show wear. I then replaced the ice chute cover and tested the ice maker. With everything working correctly, I reinstalled the panel in the door.

The icemaker assebly would go off track

  • Customer: Donna from The Villages, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 5 of 5 people found this instruction helpful
I removed the front cover--just popped off with no trouble. Removed 2 screws at the bottom. Slid the broken part out and put the new one in place. Put in the two screws, replaced the fron cover AND Done!!!
BTW I am a 65 year old woman and the icemaker is like new.

didn't eject icecubes

  • Customer: Ronald from Marion, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 6 of 8 people found this instruction helpful
R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic.
Very Satisfied,
Ron Martin
All Instructions for the LSD2615HEW
76-90 of 710