Models > LSD2615HEW > Instructions

LSD2615HEW Admiral Refrigerator - Instructions

All installation instructions for LSD2615HEW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LSD2615HEW
541-555 of 710
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice Maker was not functioning

  • Customer: BRET from SAN DIEGO, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed your posted video. Did step by step as video instructed and in about 30 minutes finished. Ice was made approx 30 minutes later. I hope you do more videos, a picture is worth a thousand words.

changing the water/ice filter

  • Customer: Ellen from Fairfield, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Opened up the compartment where the old filter was located, twisted it to take it out (be careful not to spill water in the filter!), and installed the new one. Even a 64 year old woman had no trouble!

Ice cubes would not dispense out of the door

  • Customer: Joseph from San Marcos, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replace the Auger & Crusher blade. Very easy to do and it works great now. Also, your customer service was great!! shipped the same day and arrived to me the next day!!

Frost in bottom freezer, freezer 8%, ice maker works

  • Customer: Richard from Smyrna, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net

Leaking water

  • Customer: Terry L. from Glasgow, KY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed Ice bin, remove rails on left side that hold ice bin. Remove one screw holding ice maker to refrigerator wall,then lift ice maker off holding screws. Unplug wire harness from back of refrigerator. Remove wire harness and loading wire from old ice maker and install on new unit. Re-install new ice maker by reversing steps. Videos where very helpful.

Ice maker not working

  • Customer: Charles from Middletown, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed on line instructions. Instructions were very helpful. The part was an exact replacement. Everything went as planned.

Was Not Making Ice

  • Customer: Don from Desert Hot Springs, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the Video, and it went almost as the video, except for the rails for the ice tub, so instead of the nut driver, had to use an open end 1/4" wrench. Now its a working with lots a ice....

Icemaker

  • Customer: BETTY from HOCKLEY, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I received the new icemaker the next day after I had ordered it. After watching the video on how to install the icemaker I installed it within a few minutes which I really surprised myself since this was my first repair job to do by myself. The new ice maker has been working great and I am very pleased with partselect and will continue to contact you when I am in need of any parts. Thank you, betty

dripping and making globs of ice

  • Customer: Edward from Philadelphia, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1 removed ice basket 2 remove cover over basket 3 unplug power cord 4 loosen top screws with 1/4 in nut driver (do not remove the completely) 5 remove lower mounting screw ( not necessary to remove basket rail) 6 remove ice maker from unit 7 remove bale from old unit 8 install bale on new unit 9 remove front cover from old unit 10 remove power cord from old unit 11 plug in cord to new unit 12 install old front cover on new unit 13 mount unit in freezer 14 hang unit on top screws 15 install bottom screw 16 plug in unit 17 put in ice basket and cover. no runs, no drips, no errors. Ice was made in about 2 hours.

Ice Maker stops working..

  • Customer: Tony from Litchfield Park, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Fast delivery...Great video instructions..The only difficulty is when I tried to take the cable out. It's kind of hard and far away from my reach. So, I took only the cable out on Ice Maker end.

Ice maker tray in side by side leaked and created large lumps of ice

  • Customer: Catherine from Punta Gorda, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug refrigerator, turned off water to ice maker, unscrewed bracket, lifted ice maker off clips, pulled out water hose,disconected wiring harness and lifted out old icemaker. Reversed the process and it worked like a breeze and no service call. Space is very tight and you have to do a lot of feeling without actually seeing what you're doing and you need a small flashlight. It was so easy with diagram provided on PartSelect's website.

Stopped making ice, leaking water into freezer to kitchen floor!

  • Customer: John from Seabrook, NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Found PartsSelect on internet. Read data, watched remove/replace video, ordered new Ice Marker. Arrived in 11/2 days-quick. Both removel and install very easy; three easy to remove screws, disconnect wire harness pull it out. However, water cup on end of the new Ice Maker was faceing 90 degrees the wrong way! Had to totally disassemble both new and old Ice Makers to swap water cups. Reassemble, pray it was done correctly and install. New Ice Maker works like a champ and no leaking--Thanks PartsSelect.

My refrigerator light did not work.

  • Customer: Fred from Warwick, RI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After years of using a flash light to check the contents of my refrigerator, I decided to try to fix the problem myself. Replacing the light switch was very easy. The directions were straight forward and I'm sorry I waited so long to tackle the problem.

new maytag filter clogged twice in two weeks no ice or water

  • Customer: Jim from Gleason, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out 2nd new filter $43.00 each that clogged in less than 2 weeks each and installed in 2 mins. this bypass and ice and waterr work perfect.Thank you, thank you for your exceptional service ordered part and it came next day without extra charge,great service.

Ice wheelce wheel was broken, ice maker not working and bucket cracked

  • Customer: Edward from Shepherd, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Removed bucket,and removed the front cover. the ice wheel was removed by removing the nut from the blade assembly and removing the blades washers and spacers. The parts were replaced in reverse order and the nut replaced. The ice maker was removed by removing the bottom bolt, loosening the two side bolts and lifting the unit off the bolts. the cover was removed from the ice maker and the tab depressed on the wiring harness which was then unplugged. The wire was removed and replaced on the new unit the harness plugged into the new unit and cover replaced. The unit was the placed back on the bolts, tightened and the bottom bolt replaced. the ice bucket was replaced and unit turned on. Ice making within an hour.
All Instructions for the LSD2615HEW
541-555 of 710