Models > LSD2615HEB > Instructions

LSD2615HEB Admiral Refrigerator - Instructions

All installation instructions for LSD2615HEB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LSD2615HEB
661-675 of 697
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Severely cracked vegetable/fruit crisper pan

  • Customer: Clifford from Lake Villa IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I opened the refrigerator door and removed the cracked crisper pan. Removed the vegetables and placed them in the new crisper and returned it to the refrigerator. Installation was less than 1 minute!

Ice maker leaking water dripping into the bin and freezing the dispensing unit

  • Customer: Richard from Port Orange FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I checked the part number and an exact replacement was ordered. The old unit was removed and what I failed to note was that the water supply hose for the new unit entered from the side. Further examination showed a small "break-out" piece at the rear of the unit. but I still had to do something about the hole in the side. I used a piece of metal tape to close off that hole, trimmed it to size, and installed the unit. It was really an easy install after I figured out what to do about the hole. Evidently, this unit is mounted on the side of the freezer compartment in some models. Reading the reports of others was a big help.

Refrigerator and freezer stopped cooling. Compressor pump not coming on

  • Customer: Joseph from North Anddover MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the cover panel. There is a clip that holds the relay and capacitor to the pump. Use a screwdriver to pry it off. Unplug the relay. The capacitor is plugged into the relay and they come together which was a surprise, I thought I only ordered the relay. Unplug a cable from the relay. Insert that cable into the new relay and plug it into the compressor. Reattach the clip. One be important instruction. Unplug the refrigerator for at least 8 hours before installation to allow the compressor to cool down. I tried first without allowing the compressor to cool and it did not work. After letting it cool I tried again and it worked like charm. Make sure the refrigerator is unplugged when doing the repair

Old ice maker worked irratically and finally quit for good.

  • Customer: Richard from Peoria AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video and advice from the many others on this site and only have a few additional comments. First, the decorative cover on the front of the old unit is held on with two plastic teeth on the top and bottom of the cover. This was not at all apparent and it took me awhile to figure it out. I used a sharp knife to pry up the top edge until the teeth lost their grip on the metal notches in the old unit. Second, don't try to pull the cables out of the front of the old unit before removing that cover. It is held in with a plastic snap that must be depressed after the cover is removed. The video does a good job explaining how to remove the old metal arm and attach it to the new unit so that it will recognize the ice level in the bucket. Finally, don't bother looking around the web site for a button that enables you to add to these comments. You'll be contacted by email in a week or two for that.

ice maker quit making ice

  • Customer: denton from grinnell IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged the refrigerator.Removed the nut on the front bottom side from the support bracket with a nut driver.Pull down and out the old icemaker but not clear out to remove the electrical connector reaching to the back . Re-used the old front cover and the wire support clips and the wire connector assembly.Also put the shut off wire on the new icemaker.Re-installed in reverse sequence and waited for ice cubes to be made.Make sure the water line coming in the back goes to the ice tray.

Ice maker had been leaking for several months and needed replaced

  • Customer: Joe from Leonard TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took the old part out and put the new one in and it works like it should. I loosened two screws and took one screw out with nutdriver. then I used the old wiring harness, bail and cover to finish.

The ice maker had been dripping and than stopped making ice. I worked with it and got it to work again for a few days and than the same problem occured.

  • Customer: Kathleen from Waller TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on line first. I shut off the power to the refreigerator. I took the one screw out on the bottom of the ice-maker and pushed up on the ice maker. Than I disconnected the power harness inside the refrigerator. I took it out and changed out the harness from the old one to the new one and also the bar that dumps the ice. I reconnectected the harness to the back of the refrigerator, made sure that the water spout lined up correctly. Pushed the ice maker down on the screws and reconnected the screw that I had removed. Waited about 1 hour and had ice cubes. This was an easy process after watching the video.

Broken light switch

  • Customer: John from Pepperell MA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Installing the switch was a breeze, the tough part was removing the old switch. I watched a video on the PartSelect website which showed how to remove and reinstall the switch. I attempted to remove the switch the same way that they showed on the video, but the problem was my switch was surrounded with foam insulation which was stuck to the old switch. I attempted to pull out the switch but was not able to extricate the switch. Finally, I called a friend who works with these switches and he cut away the foam insulation and removed the switch. Being the handyman that I am, I was able to reinstall the new switch. Hope this helps anyone with an Amana refrigerator that has the light switch on the side wall instead of in the light console like the video showed. Don't be afraid to cut away the foam on the right and left sides and the bottom. Don't cut away at the top, because that is where the wire connections are located and you might cut those off and then you'll be ordering more parts. Good luck.

Crisper Pan and Frame

  • Customer: Barbara from DRACUT MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I didn't have anything difficult to fix it was basically just removing the crisper frame and pan and installing the new one. I will however say that I was very impressed with how quickly my replacement parts were delivered.

Moved into a new apartment and this part was missing from the refrigerator so the bottom crisper was not functional.

  • Customer: Linda from Biscayne Park FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Was a very tight fitting part and it had to be gently tapped into place.

Ice maker was leaking water.

  • Customer: Curtis from Rock Rapids IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed screw from bracket on bottom side of unit then loosened the two screws on top side. Lifted unit off the two upper screws unpluged wires took cover off and removed ice arm, reinstalled all on new unit and installed it back in freezer. Did this in less than 10 mns.

Ice Maker Not Working

  • Customer: Corey from Bridgeton MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
This process actually took 3 tries to resolve. Read the entire article it may save you money.
Before each trial I shut off the water and unplugged the refrigerator.
Trial 1
I went to the website and chose the part that had the highest percentage of resolution (78%), which was the actual icemaker. I followed the direction that another person described in detail how to replace. It was easy but it wasn’t the solution. It took me 15 minutes to switch out using a screwdriver and a nut-driver. Turned on the water and plugged the refrigerator in. However, after doing so I still had no ice.
Trial 2
Next, I tried replacing the small water pump that pumps water up to the ice maker. The part is called
the “Double Outlet Water Valve”. Here again on the premise that it was the next highest percentage part to fix my problem. I replaced this part in about 15 minutes with an adjustable wrench and a knife. This time a turned on the refrigerator and water squirted out of the plastic hose that feeds into ice maker’s water feed tube. Still no ice.
Trial 3
The last part to replace was the water feed tube which is a vinyl tube that extends from the outside back of the refrigerator to the ice maker. I read that if water shoots out of the plastic hose that attaches to the “Water Feed Tube” is most likely frozen. So, I replace the “Water Feed Tube”. I disconnected the plastic hose in the back and took some pliers and pulled the “Water Feed Tube” out from the back. It was frozen solid. I cut the new “Water Feed Tube” to the same length and inserted it into the back of the refrigerator. I will most like not go in all the way until you guide it in to the icemaker from inside the freezer. I used some good clear silicone caulk around the outside of the “Water Feed Tube” and attached the plastic hose to it with a small clamp. I was done in about 15 minutes. I plugged in the refrigerator and I let the caulk fully dry for 24 hours. Then I turned on the water. Within the hour I had ice. Finally!
What I determined was the “Water Feed Tube” froze up and caused the “Double Outlet Water Valve” to fail. So, it was necessary to replace both but not the ice maker. What happens in the process of making ice is as the ice maker cycles it calls for water from the “Double Outlet Water Valve”. You should first check to see if the “Water Feed Tube” is frozen. Remove it, use a hair dryer to thaw it out. Reinsert it and re-clamp it to the plastic hose. If that doesn’t resolve your problem or you find that it wasn’t filled with ice, make sure the “Double Outlet Water Valve” is pumping water to the ice maker. If it is, then, replace the ice maker. If it isn’t, replace the “Double Outlet Water Valve”. In other words, don’t go on the percentages. Go on the cheapest.

Bottom freezer was making constant grinding noises, then stopped making ice altogether. I researched the Amanda site, read the customer feedback info and instructions to replace the ice maker. We've been fortunate to have had no ice maker issues for this Amana unit for ten years! The fridge and fre

  • Customer: Sharon from Mukilteo WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled out the fridge, emptied the freezer, followed the video, which was very helpful. I watched it three times.

Chunks of non stick coating coming off. Water leaking into ice collection container.

  • Customer: Chris from jackson GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
1.Pull refrigerator out from wall and unplug. 2.Turn the water source off! 3.Remove one screw from bottom and loosen two screws at the top of the ice maker. 4.Pull ice maker down and unplug the power connector. It has 2 locking tabs so press to release the lock. The water tube will pull out on it's own.5. Remove the cable, front cover and clips from old unit and install on the replacement unit.6.Re-Install new ice maker in reverse order. Always a good idea to take pictures before you do changes in case you are not sure.

water dripping from ice maker dual valve went bad

  • Customer: Harold from escalon CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
the repair was very easy,used 1/4 inch nut driver removed the necessary screws from mounting plate and dual valve. removed all lines from old valve cut 1/4 inch from tip of lines and replaced into new valve. replaced electrical leeds and resecured plate and valve.
All Instructions for the LSD2615HEB
661-675 of 697