Models > LSC27910ST > Instructions

LSC27910ST LG Refrigerator - Instructions

Installation Instructions for parts on models starting with LSC27910ST

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with LSC27910ST

All Instructions for models starting with LSC27910ST
1-9 of 9
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sticking Ice dispenser

  • Customer: James from Englewood FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 15 people found this instruction helpful
After checking the prices of new refrigerators, I decided that I had nothing to lose trying to repair the sticking ice/water dispenser. I followed the previous instructions by prying off the panel with a screwdriver working my way around. Some effort is needed, but it will come loose before it breaks. You should remove the funnel first. If you have an older model, the funnels are fragile and should come out with a gentle back and forth jiggle. I broke mine. After pulling the face off the frig,I noticed that the plastic piece the activates the dispenser was partially out of its cradle in the rubber piece. Apparently pushing too hard on it can dislodge this piece and cause the unit to stick. Check this out before going for a new actuator. It only took a few minutes to clean and reassemble and reinstall. Works perfectly. Received new funnel and it was different than the one I took out. I missed the note that said if you order the funnel, you should also get the bracket to be sure they go back together. Two lessons learned. Don,t be afraid of this repair and don't push too hard on the dispenser.

Rails broke when overloaded

  • Customer: James from Bremerton WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed shelf that rails were mounted to. Used a std phillips screwdriver to loosen screws attaching the rails, three per side. Removed damaged rails, lined up new rails and tightened screws. Returned shelf to refrigerator and inserted tray on the new rails.

gaskets worn out again

  • Customer: Keith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced gaskets for the second time in four years

Both guide rails had cracked at the front end I guess do to excessive weight in the drawer.

  • Customer: Robert from Parkland FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Simply removed the drawer, then removed the shelf above which held the guides, removed the guides ( 3 screws per side )and replaced them.

Ice cubes did not drop out of tray when the ice maker cycled

  • Customer: Michael from Eagle WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1) Take out 3 screws from top of icemaker. 2) Unplug electrical connector from wiring harness. 3) Remove icemaker unit from freezer and then remove frozen cube sensor with clip and rear insulation. 4) With your hands pull cube tray motor out of the holding clips with the tray- if this is too difficult, spread bracket and only remove the tray from the unit. 5) Insert new tray into slots and install new or existing ice sensor, insulation, and sensor clip. 6) Reinstall icemaker unit to ceiling of freezer, don't forget to plug into wiring harness. 7) Turn unit on and make some ice!

The rails for our cheese drawer broke

  • Customer: wendy from west chester PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just unscrew screws from old rails (still in refridgerator ), and screw them into new rails. We tried to order these parts from another online part site and we got the wrong parts. Partselect.com had drawing of our fridge and it was very easy to navigate through the web site. Thank you!

Motor wouldn't work to turn the fan to keep fridge cool.

  • Customer: Kim from West Mifflin PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I am a woman and I did this in about 10 mins. I turned off the water, disconnected the water line, took the back off the fridge, disconnected the motor plug and unscrewed the fan. It took a little maneuvering to get the fan out but once I did it was a breeze. Opened up back door that housed the motor, took the motor out and put in the new one. Put everything back together and it's working great. Very fast shipping so don't pay for the expedited way to ship. I ordered Sunday night and it was in my door by 10:00 Tuesday morning.

Bad fan motor and fan support assembly

  • Customer: Darryl from Rowlett TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The fan motor is easy to replace after the lower cover on the back of the refrigerator is removed. There is a drain tube (1 screw) that has to be removed in order for the fan support to be removed.

Ice tray was bent and spilling water onto ice making it freeze

  • Customer: William from Nolensville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I took the ice out with one screw and took out the old tray the new one slipped right in and I hooked up the little heat strip with one snap works perfect cost $10 I was told by appliance repair tech that I needed to replace the ice maker for $450 saved $440 dollars replacing the bent or warped ice tray
All Instructions for models starting with LSC27910ST
1-9 of 9