Models > LSC26905SW > Instructions

LSC26905SW (ASWCLGA) LG Refrigerator - Instructions

All installation instructions for LSC26905SW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LSC26905SW
1-14 of 14
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My ice maker overflowed water and made a mess in the freezer

  • Customer: steve from clarence center NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The part was extremely easy to replace. The unit came out with one screw, and I had to unplug the wire connection. After removing I noticed the ice tray was cracked - that's what caused the problem. The new unit went in easily with 1 plug in connection and 1 screw. I was done in less than 10 minutes.

Rails broke when overloaded

  • Customer: James from Bremerton WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed shelf that rails were mounted to. Used a std phillips screwdriver to loosen screws attaching the rails, three per side. Removed damaged rails, lined up new rails and tightened screws. Returned shelf to refrigerator and inserted tray on the new rails.

Both guide rails had cracked at the front end I guess do to excessive weight in the drawer.

  • Customer: Robert from Parkland FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Simply removed the drawer, then removed the shelf above which held the guides, removed the guides ( 3 screws per side )and replaced them.

entire ice maker unit broken

  • Customer: MARCUS from ALEXANDER CITY AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the ice maker assembly and the ice container auger assembly. Installation was fast,considering that I was able to look at how the old unit was installed and simply copied what I saw. The parts were the exact same which made installation easy. There was only one screw that needed to be removed inorder to take the old unit out. The new unit is easily put back in it's place, and the one screw put back in. This was the quickest and easiest, "do it yourself" job, that I have ever done. Thanks for everything Part select.

refrigerator light stayed on when door was closed & heat from lights melted plasted parts

  • Customer: Barry from Baton Rouge LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced both push button lights (french doors on refrigerator) and replaced plastic parts on overhead lights (note: ordered/or was sent wrong type pushbutton light switches - with one phone call was reinbursed cost of these switches & was sent correct switches 3 days later) with no hassle

Ice cubes did not drop out of tray when the ice maker cycled

  • Customer: Michael from Eagle WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1) Take out 3 screws from top of icemaker. 2) Unplug electrical connector from wiring harness. 3) Remove icemaker unit from freezer and then remove frozen cube sensor with clip and rear insulation. 4) With your hands pull cube tray motor out of the holding clips with the tray- if this is too difficult, spread bracket and only remove the tray from the unit. 5) Insert new tray into slots and install new or existing ice sensor, insulation, and sensor clip. 6) Reinstall icemaker unit to ceiling of freezer, don't forget to plug into wiring harness. 7) Turn unit on and make some ice!

Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b

  • Customer: Sarah from Elk Grove CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!

Broken ice auger

  • Customer: David from Katy TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
New part fit perfectly.

The rails for our cheese drawer broke

  • Customer: wendy from west chester PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just unscrew screws from old rails (still in refridgerator ), and screw them into new rails. We tried to order these parts from another online part site and we got the wrong parts. Partselect.com had drawing of our fridge and it was very easy to navigate through the web site. Thank you!

Motor wouldn't work to turn the fan to keep fridge cool.

  • Customer: Kim from West Mifflin PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I am a woman and I did this in about 10 mins. I turned off the water, disconnected the water line, took the back off the fridge, disconnected the motor plug and unscrewed the fan. It took a little maneuvering to get the fan out but once I did it was a breeze. Opened up back door that housed the motor, took the motor out and put in the new one. Put everything back together and it's working great. Very fast shipping so don't pay for the expedited way to ship. I ordered Sunday night and it was in my door by 10:00 Tuesday morning.

light was not going on sometimes, or needed wiggling to work

  • Customer: Nancy from Hallandale Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
purchased a new switch. The old switch just needed to be lightly pried out with a screw driver, then it was simple to unplug the old, and plug in the new. Voila! Light !

Bad fan motor and fan support assembly

  • Customer: Darryl from Rowlett TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The fan motor is easy to replace after the lower cover on the back of the refrigerator is removed. There is a drain tube (1 screw) that has to be removed in order for the fan support to be removed.

Ice tray was bent and spilling water onto ice making it freeze

  • Customer: William from Nolensville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I took the ice out with one screw and took out the old tray the new one slipped right in and I hooked up the little heat strip with one snap works perfect cost $10 I was told by appliance repair tech that I needed to replace the ice maker for $450 saved $440 dollars replacing the bent or warped ice tray

Threads were striped on water valve leaked needed new one

  • Customer: Nicholas from Melborne FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Shut water valve off drained water in refrigerator instAlled new valve
All Instructions for the LSC26905SW
1-14 of 14