Models > LRSC26912TT > Instructions

LRSC26912TT LG Refrigerator - Instructions

All installation instructions for LRSC26912TT parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LRSC26912TT
1-8 of 8
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sticking Ice dispenser

  • Customer: James from Englewood FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 15 people found this instruction helpful
After checking the prices of new refrigerators, I decided that I had nothing to lose trying to repair the sticking ice/water dispenser. I followed the previous instructions by prying off the panel with a screwdriver working my way around. Some effort is needed, but it will come loose before it breaks. You should remove the funnel first. If you have an older model, the funnels are fragile and should come out with a gentle back and forth jiggle. I broke mine. After pulling the face off the frig,I noticed that the plastic piece the activates the dispenser was partially out of its cradle in the rubber piece. Apparently pushing too hard on it can dislodge this piece and cause the unit to stick. Check this out before going for a new actuator. It only took a few minutes to clean and reassemble and reinstall. Works perfectly. Received new funnel and it was different than the one I took out. I missed the note that said if you order the funnel, you should also get the bracket to be sure they go back together. Two lessons learned. Don,t be afraid of this repair and don't push too hard on the dispenser.

The water filter needed to be replaced.

  • Customer: Alice from Wimberley TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I screwed the old one out and replaced it with the new one. A no-brainer. The thing that was so amazing was that I ordered the filter on the intrnet and it arrived the very next day!!! I was very surprised and pleased with the very quick shipping!!!

My ice maker overflowed water and made a mess in the freezer

  • Customer: steve from clarence center NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The part was extremely easy to replace. The unit came out with one screw, and I had to unplug the wire connection. After removing I noticed the ice tray was cracked - that's what caused the problem. The new unit went in easily with 1 plug in connection and 1 screw. I was done in less than 10 minutes.

Ice cubes did not drop out of tray when the ice maker cycled

  • Customer: Michael from Eagle WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1) Take out 3 screws from top of icemaker. 2) Unplug electrical connector from wiring harness. 3) Remove icemaker unit from freezer and then remove frozen cube sensor with clip and rear insulation. 4) With your hands pull cube tray motor out of the holding clips with the tray- if this is too difficult, spread bracket and only remove the tray from the unit. 5) Insert new tray into slots and install new or existing ice sensor, insulation, and sensor clip. 6) Reinstall icemaker unit to ceiling of freezer, don't forget to plug into wiring harness. 7) Turn unit on and make some ice!

Water and Ice dispensing just stopped working. Also Ice trap was broken.

  • Customer: BRENT from Glendale AZ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Water valve replacement at back bottom right. Removed, water supply line and old valve with 1 screw and removed clips from hoses. Replaced with new valve and re-clipped hoses. Easy fix! Cleaned coils and back with blower and vacuum cleaner while I was in there too. I also had leak in water supply line, replaced. Ice trap door replacement was a little more challenging. Hard to get off the ice dispenser funnel (Part# 278D). Has 4 lock clips on it and 1 broke when I took it off. This part# 278D is not available from part select?? Tricky to replace the trap door itself. Have to make sure the door valve sits in solenoid correctly. Installed wrong the first time and door would not open/close. Had to go in and reset orrectly. Works like a charm now. Still need part# 278D!!

Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b

  • Customer: Sarah from Elk Grove CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!

Ice tray was bent and spilling water onto ice making it freeze

  • Customer: William from Nolensville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I took the ice out with one screw and took out the old tray the new one slipped right in and I hooked up the little heat strip with one snap works perfect cost $10 I was told by appliance repair tech that I needed to replace the ice maker for $450 saved $440 dollars replacing the bent or warped ice tray

Threads were striped on water valve leaked needed new one

  • Customer: Nicholas from Melborne FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Shut water valve off drained water in refrigerator instAlled new valve
All Instructions for the LRSC26912TT
1-8 of 8