Models > LRSC21935TT > Instructions

LRSC21935TT LG Refrigerator - Instructions

All installation instructions for LRSC21935TT parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LRSC21935TT
1-7 of 7
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

BROKEN PLASTIC SUPPLY ICE MAKER

  • Customer: Norman from Saint Clair Shores MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
SECOND TIME I HAD TO REPLACE INFERIOR PLASTIC TUBING BEING THE SIZE IT IS YOU CAN'T BUY IT AT ANY STORE. 5/16 can't find pex in that size.

Ice cubes did not drop out of tray when the ice maker cycled

  • Customer: Michael from Eagle WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1) Take out 3 screws from top of icemaker. 2) Unplug electrical connector from wiring harness. 3) Remove icemaker unit from freezer and then remove frozen cube sensor with clip and rear insulation. 4) With your hands pull cube tray motor out of the holding clips with the tray- if this is too difficult, spread bracket and only remove the tray from the unit. 5) Insert new tray into slots and install new or existing ice sensor, insulation, and sensor clip. 6) Reinstall icemaker unit to ceiling of freezer, don't forget to plug into wiring harness. 7) Turn unit on and make some ice!

The water line was leaking

  • Customer: Awilda from Staten Island NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the damaged tube and replaced the it with a new one.

Water and Ice dispensing just stopped working. Also Ice trap was broken.

  • Customer: BRENT from Glendale AZ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Water valve replacement at back bottom right. Removed, water supply line and old valve with 1 screw and removed clips from hoses. Replaced with new valve and re-clipped hoses. Easy fix! Cleaned coils and back with blower and vacuum cleaner while I was in there too. I also had leak in water supply line, replaced. Ice trap door replacement was a little more challenging. Hard to get off the ice dispenser funnel (Part# 278D). Has 4 lock clips on it and 1 broke when I took it off. This part# 278D is not available from part select?? Tricky to replace the trap door itself. Have to make sure the door valve sits in solenoid correctly. Installed wrong the first time and door would not open/close. Had to go in and reset orrectly. Works like a charm now. Still need part# 278D!!

water supply to ice maker leaked

  • Customer: john from locust valley NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Gave model number on website, found picture of icemaker section. Ordered part that came in 3 days and switched old for new

Leak in water filter supply line

  • Customer: John from Pacific MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I found a crack in the pex line from the valve up the back of the refrigerator to the water filter. I could not find the correct 5/16" size line locally to replace it. A guy in plumbing at Home Depot said he always repaired them by cutting out the crack and finding a piece of clear vinyl line that would fit tightly over the cracked pex to splice in a fix with hose clamps. I did that and it was a really bad idea. The line was obviously fatigued and failing because it just cracked further up and leaked again. I then looked up and ordered the correct line (actually both the supply and return since they were available). Installing the new lines was a breeze. The pex connectors are simple to disconnect and reconnect. Wish I had done that to start with. I looked for a youtube video for the proper replacement steps but all I found was a video of a guy who cut out a crack and stuck a pex connector in to replace the cracked section. By doing that he pulled slack from the valve end of the line which didn't exist and cracked the line again. I don't know why anyone would mess with patching one of these lines. The correct parts are available, cut to the right length, and removing and replacing them at the valve and the filter is dead simple.

Ice tray was bent and spilling water onto ice making it freeze

  • Customer: William from Nolensville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I took the ice out with one screw and took out the old tray the new one slipped right in and I hooked up the little heat strip with one snap works perfect cost $10 I was told by appliance repair tech that I needed to replace the ice maker for $450 saved $440 dollars replacing the bent or warped ice tray
All Instructions for the LRSC21935TT
1-7 of 7