Models > LRSC21934SW > Instructions

LRSC21934SW LG Refrigerator - Instructions

All installation instructions for LRSC21934SW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LRSC21934SW
1-6 of 6
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice cubes did not drop out of tray when the ice maker cycled

  • Customer: Michael from Eagle WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1) Take out 3 screws from top of icemaker. 2) Unplug electrical connector from wiring harness. 3) Remove icemaker unit from freezer and then remove frozen cube sensor with clip and rear insulation. 4) With your hands pull cube tray motor out of the holding clips with the tray- if this is too difficult, spread bracket and only remove the tray from the unit. 5) Insert new tray into slots and install new or existing ice sensor, insulation, and sensor clip. 6) Reinstall icemaker unit to ceiling of freezer, don't forget to plug into wiring harness. 7) Turn unit on and make some ice!

Unit kept beeping as if the freezer door was open

  • Customer: Paul from San Jose CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I popped the old switch out of place and then disconnected the wire harness from the switch with a pair of needle nose pliers. I then inserted the harness into the new switch and popped the switch into place. Super easy and fast.

Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b

  • Customer: Sarah from Elk Grove CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!

Ice tray was bent and spilling water onto ice making it freeze

  • Customer: William from Nolensville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I took the ice out with one screw and took out the old tray the new one slipped right in and I hooked up the little heat strip with one snap works perfect cost $10 I was told by appliance repair tech that I needed to replace the ice maker for $450 saved $440 dollars replacing the bent or warped ice tray

light out

  • Customer: Jack from Ellenton FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
slid screw driver under edge of switch, easy.

Threads were striped on water valve leaked needed new one

  • Customer: Nicholas from Melborne FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Shut water valve off drained water in refrigerator instAlled new valve
All Instructions for the LRSC21934SW
1-6 of 6