Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LNC7766B71 > Instructions

LNC7766B71 Admiral Dryer - Instructions

All installation instructions for LNC7766B71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC7766B71
61-75 of 689
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No power, no light, Thermal/high limit fuses blown

  • Customer: William from Monroe, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 5 of 5 people found this instruction helpful
Open the lid, replaced the small fuse on top( one wire at a time). Removed the heating element, then replaced the lower fuse and re-installed the heating element. That part of the job took 15 minutes. The fuses were blown because the plastic housing inside of the front panel was completely clogged. I took the two screws off holding the front panel on, then the two torque screws on the plastic housing. I cleaned a ton of lint out of the housing and re-assembled.

My dryer was still running but the clothes were not drying. Since I didn't know if it was the heating element or the thermostat, I ordered the part that includes both.

  • Customer: Elaine from Hermitage, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
My son actually did the repair when he was over here and said it was so easy, even "Mom" could've done it! He said all he did was unscrew one little screw, life out the old part, drop the new part into that slot and replace the screw! It's the easiest repair I've ever heard of! Thank you....I will definitely order parts from your company in the future. Fast shipping too!!

My lint filter had developed holes.

  • Customer: Barbara from Oak Park, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
It was supper easy. I was able to order the correct part from the detailed description you provided. I just opened it and slid it into the slot for a perfect fit.

I wish I had done it sooner. My filter had holes in it for some time.

old latch broke

  • Customer: Jim from Germantown, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 6 of 9 people found this instruction helpful
I inserted the clip

drum wouldn't turn

  • Customer: Lisa from Woodstock, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
Actually, I was the handy man. First I removed the front panel. Then I used 3 - 2x4s to hold up the drum. Then I slipped the belt around the center of the drum ,motor,and around the pulley at the bottom of the dryer. That was it, and then I put it back together. My wife was amazed and proud that I did it without calling for help! No Problem!

Dryer Quit running

  • Customer: William from Marion, VA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
First off I want to say I ordered my motor on Sunday night at 11:30 PM on veterans day and got the two day delivery. My part was sent out on that Monday (fed. holiday) and I received it Tuesday around 1:00 pm after I disconnected the wiring harness, took the blower fan C-clips off, unscrewed about 6 screws, and pulled the assembly apart I just done everything in reverse and replaced the new motor. I discovered that my thermostat fuse was blown so I ordered the High temp thermostat kit from here (two day delivery) on Wednesday at 10:30 PM and got the parts Friday at around 2:00 PM. After taking out four screws and four wires I replaced the fuse and high temp. set, pushed the start button to see if it worked and it started up like new. Now it heats twice as fast and everything doesn't have a light burnt smell. So dry time is faster (no more 80-90 min. cycle times), less dryer sheets (to cover smell) and all this added up to cost savings on electric bill and dryer sheets. It took a week to get my dryer back (because I just looked at the motor) but in the end I needed the fuse and motor. The quick turn around time to get the parts, the pictures to see if I had the right parts, and the ease of ordering the parts meant only one run to the laundry mat, and that wouldn't have happen if the dryer hadn't messed up on laundry day.

Originally Noisey While Running

  • Customer: Gary from Park Hills, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 12 people found this instruction helpful
Unplugged electric, turned off gas valve. Opened top using a putty knife, laid it gently back against the wall for support. Removed 2 screws holding front on-leaned front out about 3-4 inches- while holding front with my knees I disconnected door switch wires.-then removed front panel. Followed instructions on maintenance sheet glued on underside of dryer top (Lucky it was there). Took tension off drive belt. Removed belt and drum following instructions on lid sheet. Removed old slides (worn out) Installed new pads & slides. Vacuumed out all lint/dust/dirt I could reach, Cheked rear drum rollers. Reinstalled everything that I had removed. It took extra time to do everything because dryer was in tight space, little working space. Turned gas on, plugged in electric cord. Worked great now.

hole in lint filter

  • Customer: vernon from chowchilla, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
ordered lint filter and it was here the next day.
GREATE SERVICE!!!!

Belt broke

  • Customer: jim from Grand Rapids, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
Real easy I have resurrected my dryer may times so this was easy to replace the belt and idler pulley

Dryer started making loud noises while running

  • Customer: Kirt from Houston, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
The repair was relativley easy. Had to remove the top, it popped up with a screwdriver and picked it up and leaned against the wall. Then removed two screws to remove the front.Removed old belt then move dryer tub forward, removed bad roller bearing, installed new bearing,applied some grease ( had to use a screwdriver to pry bearing pin off/on which is reusable.Finally installed the new belt around tub, the most trickey part since there was no access panel, but after a few tries it was easy to figure out.Great price on items and i checked several places,quality parts and delivered only a couple days after i ordered. I highly recommend partselect. Thanks Kirt

Dryer would not come up to temp.

  • Customer: Robert from Bennington, VT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 7 of 13 people found this instruction helpful
Hinged open the top of the dryer. While dryer was running I tapped on the thermostat. The heater came back on. This verified the problem. Unplugged the thermostat, unscrewed it and replaced it.

Dryer sounded like a garbage truck.

  • Customer: Philip from Granite Bay, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
The support roller broke and that made the noise as the rubber came off the wheel. It took about 8 months before the belt finally broke. Since I had it apart I decided to change both the drum felt seals and idler pulley wheel. I had trouble finding high temperature adhesive for the drum felt seal. Lowe's and Home depot didn't have anything that indicated it would take the heat. Finally located an adhesive at a craft store and the label claimed it was good on washers and dryers. Although I was able to glue and stretch the felt onto the dryer by myself if you have two people it will be alot easier. My dryer had made so much noise for so long I couldn't believe how quiet it is now.

Door would not stay shut

  • Customer: Eli from North Stonongton, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.

Broken drive belt

  • Customer: Stanley from Flushing, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 13 people found this instruction helpful
I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.

Dryer lost heat

  • Customer: James from Fulshear, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 8 of 16 people found this instruction helpful
Was obvious what the problem was when dryer lost heat. Thermostat was fried with one contact burned off.
Unplugged dryer
Opened top of dryer using putty knife to release latches.
Removed 2 wires to Therostat, and removed the old one (2 1/4 hex screws).
Installed new thermostat, and reconected.
Done
All Instructions for the LNC7766B71
61-75 of 689