Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LNC7766A71 > Instructions

LNC7766A71 Admiral Dryer - Instructions

All installation instructions for LNC7766A71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC7766A71
526-540 of 687
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken drum belt

  • Customer: Barry from Norfolk, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Used the putty knife to pry open the front of the top cover. Removed the retaining screws securing front cover to each side. Lifted front panel off bottom hooks and holding drum, removed front cover. used wood block to hold drum in place. removed broken belt and belt tension spring. Keeping the rubber side of the belt against the drum, threaded belt through the tension spring onto the drive motor flywheel. Tilted dryer backwards to hold drum in place while removing wood block. Assembled front and top in reverse order. Used pressure to secure top to spring clips.

Dryer would not start.

  • Customer: Darrin from Bowie, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video and removed old fuse. Tested with ohm meter which showed it was bad. Very very easy to replace. Video shows everything you need to know. Remember to open front panel of dryer and clean lint system! Extreme build up of lint causes dryer to over heat! Fantastic web site with all info needed to complete repairs! Thank you for all the help.

Belt Broke

  • Customer: Jeffrey from Grantsville, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Had an idea how the repair would go. The video is a great tool for someone not mechanically inclined. Easy fix and will save from paying a repair person. Suggestion .... put a small block of wood (or something simular) under the drum when you pull the front cover forward to save from having the drum drop down making sure the back seal is still seated and in place. No big deal and easily fixed if it pulls away.

old door seal came off and tore up

  • Customer: KIenny from Bloomington, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
order knew door seal fix was a snap just Snap in place

We took towles from the washer that had still contained more water, the spin cycle must have had a problem.

  • Customer: Henry from McLean, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I felt the belt had broken since the unit was still running. I went on-line looked at some you tube movies to get some idea what to do. Was very helpfull. Found on-line how to get the part forb this nearly 20 year old dryer. Had the part shipped overnight, was able to track it. Followed your innstallation instruction, With the heavy rubber bands hooks at both ends it was easy. Never done this before, sure saved a good amount of money.

Very little heat

  • Customer: Janien from Norwalk, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
This repair was so easy. All you need is a 1/4 inch nut driver or straight socket, a pair of needle nose pliers & a flat screwdriver,file or anything flat to pop the top of the dryer open. There are 4 wires to remove and 4 nuts. take the old parts out and replace with the new and replace the wires. Hardest part for me was making sure I didn't drop the nuts.I recommend watching the video. My dryer is working great.

Dryer stopped in the middle of a cycle

  • Customer: MARK from NEEDVILLE, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Went online to see if this was a common problem... found the Part Select site... watched the short repair video... thought I could give it that a try, if it worked I just saved $150.00 bucks! Sent for parts, got them in two days! The repair was quick. I bought a nutdriver for the task but it wasn't a magnetic bit...get a magnetic nutdriver! Those small screws can get away from you. I had to slowly unscrew the screws and catch them with a telescopic magnet. I was washing a load during the dryer repair in hopes the repair worked..it did and I(Mr.Mom)completed 4 loads that morning.

Belt broke.

  • Customer: Laura from Saint Albans, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After looking at your video, my brother and I put the belt back on, placed the front and back on and that was it. It required two of us but it went well and the machine is working fine. Thank you.

Heat was not on long enough

  • Customer: Michael from Royal Palm Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Less than a houre

Broken Belt

  • Customer: Joseph from Great Mills, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The belt broke at the worse possible time, with a washer full of wet clothing. Watched one of your fine repair videos, did exactly as it said and in less than 15 minutes I had the new belt on and the laundry continued as if nothing ever happened. Thank you for your help and instruction. I will continue to shop your site for all me maintenance and parts needs. Thanks again!

Broken Belt

  • Customer: Kent from Tallahassee, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This was the first time that I'd had a dryer apart, so naturally I wound up taking many more things apart than I needed. After finally removing the front panel, I could see that the old belt had broken and was wrapped around the motor shaft, and that the tensioner was lying loose. Installing the new belt was a snap. Simply put it on the lines on the drum and insert into the pulley. The only challenge was figuring out exactly how the tensioner fit. The only way that it could go, and do its job, meant putting a lot of pressure on the spring. Once I got past that hesitation, it was a breeze.

Multi Rib Belt broken

  • Customer: Primoose from Grayson, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video on your site and it is very helpful and that is only I needed.

Broken drum belt

  • Customer: Jay from Lake Ariel, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After watching the repair video that was linked in the part delivery confirmation email, the repair went really easy. I just used the putty knife to pop the lid, then removed two sheet metal screws holding the front panel with the nut driver. I disconnected the two wires from the door switch. The front panel slid right up and out. The old belt was broken and lying at the bottom of the dryer. I ran the new belt around the drum, and around the tensioner and drive pulley. This was not as difficult as I imagined it would be. I spun the drum one revolution to make sure the belt was riding right. Before I put the front panel back on I took the opportunity to clean the lint out of the blower. I then just reversed the front panel removal process and snapped the lid back down. This repair took maybe 10 minutes. If I had to do it again I could probably do it in 5. It's just that easy. The dryer works perfectly now.

Under heavy loads, dryer would turn off

  • Customer: Donald from Allentown, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Looked up on-line for tips, found computer animated video. It was easy as it looked, took longer to take dryer apart (not long). Other note on problem; neighbor who works on washer/dryers said that the motor was probably going. replaced belt anyway because I already purchased it before we spoken. Throwing caution to the wind!!

Belt had broken

  • Customer: George from Long Valley, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the online video three times. This was extremely useful. I just did what it showed. I doubt I could have fixed it without the video. This has got to be the best feature of the internet. I didn't have the exact model number, but the belt fit. I was surprised at how close the tensioning wheel was to the motor. Perhaps the belt will stretch with age and use.
All Instructions for the LNC7766A71
526-540 of 687