Models > LNC7766A71 > Instructions

LNC7766A71 Admiral Dryer - Instructions

All installation instructions for LNC7766A71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC7766A71
16-30 of 658
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer belt snapped

  • Customer: J. from Oakdale NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 26 of 30 people found this instruction helpful
There are a total of six screws that have to be removed to do this job.
Take the lint tray out and remove the first two screws.
Secondly, remove the lower panel in the front of the dryer. You do this by inserting a screwdriver at the top portion and pry it off. Next, loosen the two screws under the top panel in the front of the dryer.
Now take your screwdriver and pry up the top lid of the dryer. The last two screws are in the inside of the front panel. They hold together the front and side panels. Remove them and be sure you have a support for under the dryer drum. (once you remove the front panel, the drum no longer has a way to stay suspended)
(Make sure you disconnect the wires attached to the front door, making note of which wire goes where.)
At this point, You can follow the easy instructions that come with your new belt.
If you have a little mechanical aptitude, this is a very easy project.

Lost all power even the light.

  • Customer: Jeremiah from Laureldale PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 25 of 27 people found this instruction helpful
I removed the top and front panel. I first cleaned all the lint from the bottom of the lint trap which clogged the vent and caused the dryer to overheat. Then I replaced the high limit thermostat and thermal fuse. Bingo!! Worked good as new.

Drum stopped turning, fan continued to blow

  • Customer: Richard from Davie FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 21 of 22 people found this instruction helpful
Disconnected supply. Lifted top (hinges on rear). removed two 1/4 hex head screws retaining front panel. Disconnected door switch wires. Removed front panel, lifting off from bottom tabs. Lifted out drum and discarded broken belt. Spent 30 minutes+ cleaning interior, drum skid area, dryer exit tube, motor pulley, belt tensioner, etc, etc. Checked wiring harness for possible damage (no damage found). Repositioned drum skid pads, which had become dislodged from their intended position. Reinstalled the drum with new belt, ensuring both belt & tensioner were correctly positioned, and drum rollers and felt seals were also correctly positioned. Reinstalled front panel, tightening the two 1/4 hex head retaining screws. Reconnected power. Checked functionality. Closed top cover.

OLD DRYER KNOB BROKE

  • Customer: Donald from Keystone Heights FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 21 of 30 people found this instruction helpful
WIFE WANTED A NEW DRYER AS IT WAS USELESS WITHOUT A KNOB AND TIRED OF USING PLYERS TO TURN IT.

WENT TO INTERNET, ENTERED DRYER KNOB, LEAD ME TO YOUR SITE AND ITEM WITHIN TWO MINUTES. ORDERED AND RECEIVED IN 2 DAYS. NO TOOLS NECESSARY, JUST PUSHED IT INTO PLACE.

SAVED THE COST OF A NEW DRYER.

Dryer would not start

  • Customer: Kay from Kingsland TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 18 of 22 people found this instruction helpful
This repair could not have been easier. I went to the web site, answered a few questions and read a few examples of the repair, ordered the parts suggested and in a few days the parts arrived at my home. I opened the top of my dryer with a long handled screw driver, as suggested in the instructions, and vacuumed out the lint around the part. I called my handy son who brought over the correct tools and we followed the instructions sheet that came with the part and repaired my dryer in about 15 minutes total. It works just as it should and I am so happy. I only paid $39.00 including Shipping and Handling to repair my Maytag dryer and it works like new. Thanks to PartSelect.com! I don't think I'll ever call a repair service again.

Other collector broke and was tearing clothing

  • Customer: Michael from Bloomington IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 16 of 18 people found this instruction helpful
Opened the top by popping the two fasteners holding it down. Did this with a screw driver. Took two screws out of the front holding collector in place and two screws out holding the front to the two other sides. Put front of dryer down on the floor. Removed old collector and used all other existing material from old collector to finish job. Wife could not believe how quick this was. Put back together was a snap too.

dryer drum wouldn't turn

  • Customer: Steve from Peachtree City GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 15 of 15 people found this instruction helpful
First of all, you go in from the front. There a clip on each side that I just pried up to pop the front of the dryer up. A screw also needs to be removed in the lint catcher area. Also, two screws holding the door open switch must be removed as I never could get the electrical connectors to disconnect. No big deal. I had to figure out you must lift the front of the dryer up as the last two things holding it in are a prong on each side. Lift the front up and off and set it aside. As you do this the drum will either fall on your feet or you'll have it supported be another person or with something else. I used bungee cords and kept it in the laundry room. Cleaned out all the old lint, collected a few bucks in change. It took me awhile to figure out how the new belt routed through the removable pulley guide thing and around the wheel pulley. I don't remember right now as I'm not looking at it but remember pinching the belt and feeding it through the guide and around the wheel pulley which has a little slot and grooves matching the belt. Besides scrapping my wife's hand while she was helping me get the front of the dryer back on there were no casualties or further complications. Good luck!

No heat on dry cycle. Thought it might be element.

  • Customer: Thomas from Battleboro NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 18 of 25 people found this instruction helpful
Opened top of dryer and found high limit thermostat burned in half. Thermostat is located on top of element. Replacement of thermostat took less than 10 minutes, using phillips head screwdriver.

Replaced belt while I was in there replacing motor

  • Customer: Douglas from COMMERCE TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 14 of 17 people found this instruction helpful
If you were to do the Belt Replacement only, here is the quick synopsis:
1. Unplug dryer;
2a. Open lint door on top of dryer and remove the two phillips head screws that hold the lint bay to the metal dryer top;
2b. Next remove the two brakets holding the metal top to the dryer back (one screw on each bracket);
3. Use a flat-blade screw driver to pry off the top of the dryer (leaving the timer and start button area attached);
4. Lift off top and push back to expose just enough area so you can get to the two screws holding the dryer sides to the dryer front;
5. Unplug door switch;
6. Unscrew screws from #4;
7. With door open, lift dryer front (only about an inch) and then pry bottom of dryer front from dryer sides. The bottom of the dryer front is not screwed, just siting on Front Panel Clips;
8. Once the front is off the dryer, simply remove the belt and install the new one. Please note that while you are in here, you may want to inspect the rear drum seal and replace if it is worn to the point where metal is rubbing on metal. This is also a good time to clean out dust from inside this cavity to help extend the life of the bearings on the rollers and prevent dust from accumulating and gunking up the motor, etc.
9. Re-assemble tin the opposite order.
If you have any mechanical sense at all and you don't know anything about dryers, you will be surprised at the simplicity of the dryer.

Change dryer belt

  • Customer: Scott from Bayport NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 12 of 13 people found this instruction helpful
I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I popped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.

the drum was not turning because a broken belt

  • Customer: thomas from bloomfield NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 19 people found this instruction helpful
I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum exposed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.

Dryer not getting clothes dry in one cycle

  • Customer: Ray from Raphine VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 12 of 14 people found this instruction helpful
Raise the top of the dryer. This exposed the elements in the back. Removed old elements,paying attention to where the wires go.
Installed new elements, hooked the wires up, and I was done.

The Door Switch broke and Dryer would not run

  • Customer: Jesus from Hillsborough NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 12 of 16 people found this instruction helpful
1. Removed wires to switch
2. Lifted top panel of Dryer with a screw driver
3. removed two inside screws holding the from panel against the drum.
4. Dropped front panel on the floor and removed door switch.
5. While the door was out, I removed the lint panel attached to the door - two screws.
6. Cleaned the door panel with a vaccum cleaner
7. replaced lint panel onto door with two screws
8. replaced door switch to the front panel
9. placed front panel on to the from of dryer with two screws.
10. Connected wires onto the door switch.
11. Closed top dryer panel and them pressed hard to catch on to metal clips.
12. Attached Dryer cable to electrical outlet
13. Trurned Dryer on and open door as it tumbled to confirm it would stop.
14. Done

Dryer Not Heating

  • Customer: Timothy from Prairieville LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 13 people found this instruction helpful
This repair was so easy a sleeping Turtle could do it. You just remove the wiring from the old unit and remember which wire is on which terminal. Easily remove the old unit and replace it. Reattach the wires and you are done! Maytag is a very easy unit to work with. Just remember if you ever have to replace your Terminal Block, don't forget to order the brass nuts to attach the wires. Regular nuts will overheat and cause a fire hazard.

Dryer would not heat.

  • Customer: Deb from Milford OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 13 people found this instruction helpful
First I unplugged the dryer and slid it a few inches out from the wall. I slid 2 putty knives in the front top about 3 inches in from the sides. Released the top and raised it up. I used a multimeter to test the hi limit and the element, both were operational. I used a screwdriver to remove the 2 screws that hold the front panel in place. I lowered the panel slightly and disconnected the wires mentally noting the proper placement. With the front panel on the floor, the problem was obvious. I cleaned the lint clog under the lint screen that had caused the issue to begin with.I used a shop vac and cleaned the vent area as well as the front panel. I used a nut driver to remove the 2 screws that held the thermostat in place. The old thermostat fell apart in my hands. I covered the bare exposed wires with electrical tape. ( must have gotten HOT) and reattached the connections to the new thermostat, then replaced the 2 screws that held it secure. I stood the front panel back up and reattached the electrical connections and the 2 screws. I lowered the top and plugged it back into the outlet. I turned it on. It works like new.
All Instructions for the LNC7766A71
16-30 of 658