Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LNC6766B71 > Instructions

LNC6766B71 Admiral Washer - Instructions

All installation instructions for LNC6766B71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6766B71
61-75 of 389
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Low Cold Water Flow

  • Customer: DONALD from LENOIR, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 10 of 11 people found this instruction helpful
Replace valve by prying up the lid it is much easier than the small square entrance on back side bottom

Water Pump Failed

  • Customer: Douglas from State College, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench (Adjustable), Wrench set
  • 12 of 17 people found this instruction helpful
Obvious problem: belt destroyed. The plastic pulley on the motor was damaged beyond repair. Since you can't replace just the plastic pulley, you have to purchase another motor. The machine still would not spin. Checked the pump again. The bearings might be bad. Replaced pump; Success! washer works again. Total repair: belt $15.68, new pulley with motor $132.00, and new pump $80.00. Estimated cost to repair about $228.00. Time to troubleshoot. 1 hour, time to fix 1 hour; Total time in labor about 2 hours.

Washer Shakes And Dances

  • Customer: Adrian from West New York, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Wrench set
  • 10 of 12 people found this instruction helpful
No need to buy a brake wrench nor the expensive spring remover. Once the drum is out the washer turn it upside down and loose the screws holding the transmission about a little more than half way, to give the new snubber enough room to fit in, them tigh and assamble everything back together

The agitator came off

  • Customer: DAOSADET from WASHINGTON, DC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 10 of 12 people found this instruction helpful
use the socket with a 10 inch extention remove the existing screw. place the new agitator and screw back. remove the softner container from the broken agitator and snap it to the new one. job done.

Washing Machine was bouncing on every load

  • Customer: Hud from Woodruff, SC
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 9 of 9 people found this instruction helpful
Diagnosed that the snubber had failed.
Removed the belt, cam assembly and pulley assembly. Using Maytag brake removal tool #12002012 I removed the brake stator. I removed the front of the washing machine and the rear access plate. I removed the six tension springs. I moved the machine basket and shaft assembly toward the top of the machine. I removed the old snubber and replaced with a new one. I installed 6 new tension springs and reassembled.
The washing machine runs great.

Cover of washing machine wouldn't stay open, it fell on my wife's hand.

  • Customer: Edward from Coventry, RI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
This is a very simple repair, I opened the top of the washer by inserting a screwdriver between the top and the washer cabinet. There are 2 clips on the front of washer, locate and push in to release top. Lift top with lid attached and remove the 2 screws holding the lid to the top of washer. Remove lid and replace hinge pin and hinge.
Replace lid, close top , all done. Total time about 15 minutes or so. Now the lid will stay up and not fall on someone.

One of the two bolts that holds the motor in place broke off and since the bolts are actually embedded in the motor I had to buy the whole motor rather then just a 25 cent bolt.

  • Customer: Elmer from Fort Campbell, KY
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 18 of 37 people found this instruction helpful
First I took the front shield off, then I took the motor off.

Making Noise During Wash Cycle

  • Customer: MARK from HEBRON, KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 12 of 19 people found this instruction helpful
Removed excess water,removed hoses,tiped back washer,removed belt,removed pulley and bearing. Removed 3 screws and replaced with 3 longer screws in the stator,then removed 3 shorter screws. Then loosen very slowly each of longer screws to relieve pressure from the brake spring. Once loose,pulled out brake rotor. Replaced with new parts. Works like new.

original Factory Water Pump Bearing seized up

  • Customer: Bill from Mount Pleasant, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 9 of 10 people found this instruction helpful
Vey Easy to Fix. 1)Turn Water off at the wall. 2)Remove access panel on back of washer. 3) Remove Water pump. It is bolted down to the bottom of the washer by three nut head bolts. when loose the pump can be manipulated and tilted so the belt will have slack and most likely fall right off. Have a bucket ready. Remove water hose from top of pump by sgueaing clam with pliars and sliding clamp up hose. allow to drain in bucket. Lift drain hose out from wall and allow to drain through the pump into bucket. remove hose from pump that goet to drain. Replace pump and reverse steps listed above.

Washer made a loud noise during spin-eventually stopped spinning

  • Customer: Christopher from Haverhill, MA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
I was able to get the belt off easily but the belt was fine. I changed the snubber easily also. But that wasn't the problem. I went through all the parts that are easy enough to change without a mechanic but turned out it was something inside the innerbasket and we had to junk the washer and it was only 4 yrs old.

Water wouldn't stop

  • Customer: Steven from Westfield, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 9 of 11 people found this instruction helpful
Unplugged washer then took back off control panel. Removed clamp and tube from pressure switch. Pushed in tabs with a screwdriver and lifted top. Removed clamp and broken tube. Put new tube in place and tighten clamp with nutdriver. Closed top and put other end of tube on pressure switch with clamp. Put back on control panel and plugged in. Clamps are to big for application but do work. So far so good!

would'nt wash w/out getting hot

  • Customer: Emery from Talladega, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 9 of 12 people found this instruction helpful
just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go

agitator broke

  • Customer: Mark from Voorheesville, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
Removed old 'Agitator Auger and Post Assembly' held in place by one bolt and placed new 'Agitator Auger and Post Assembly'. SIMPLE and good price.

Lid switch had deteriated over time and no longer made contact

  • Customer: James from Rochester, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
removed the screw holding the actuator, ordered the new part and replaced it when it arrived. Shipping was really fast and I even received it one day early.

Plastic hinge pin broken on top cover

  • Customer: Daniel from Slatersville, RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
First push inner tub to left rear, all the way, and
unscrew hinge from inside of tub. repeat same on
right side. lift cover off and unscrew other half of
hinge off cover, both sides.reverse procedures and your done.
Note: always replace both hinge's new while
you have it apart.
All Instructions for the LNC6766B71
61-75 of 389