Models > LNC6766B71 > Instructions

LNC6766B71 Admiral Washer - Instructions

All installation instructions for LNC6766B71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6766B71
1-15 of 374
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

One of the plastic hinge pins brroke

  • Customer: Allen from North Little Rock AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 462 of 459 people found this instruction helpful
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.

Washer jumping in spin cycle (white flakes under the washer)

  • Customer: David from Butler PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 154 of 163 people found this instruction helpful
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING (DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK) Install the new ring, tighten the screws and put the tub back in connecting everything back up and use the 6 new springs. It really isn't that hard to do.

The belt and pulley on the drive motor broke

  • Customer: Michael from Warminster PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 97 of 123 people found this instruction helpful
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed.
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.

bearing on water pump siezed

  • Customer: kevin from rochester NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 81 of 90 people found this instruction helpful
back panel,belt two hoses,three screws, $100 dollars for the part!! pump is a molded part with a bearing insertion, is made in USA ! I'm guessing around 7 to 10 dollar manufacturing cost. I'm thinking that kind of mark-up is only exceded by the pharmacutical industry. I'm looking to buy a used machine for parts!!

EXCESSIVE Banging, shaking and squeaking while on Spin Cycle

  • Customer: robert from simpsonville SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 71 of 74 people found this instruction helpful
1)Start with empty washing machine.
2)Disconnect Hot, Cold, Power and Drain lines
3)Move machine to open area, open top by popping 2 front retaining clips.
4)Remove Front panel, remove small clear water level hose at lower rear of tub.
5)Remove small Rear access panel, disconnect large tub drain hose from pump and drain into small container, about 4 cups of water will come out.
5)Remove the 6 suspension Springs.
6)Place two large towels next to washer and tip machine onto its side slowly.
7)Remove drive belt from bottom, and slide out wash tub assembly thru top opening, be Careful not to damage large Plastic drive pulley on bottom of tub.
8)With tub upside-down, remove drive pully small plastic cover in center, remove E-Clip and remove pulley.
9)Slowly loosen snubber ring retaining bolts a few turns, DO NOT Remove, just loosen enough until snubber is free to move around.
10)Remove snubber ring by walking it around the retaining ring and install new snubber.
11) Clean machine cabinet and clean machine base where snubber touches with alcohol or Windex.
12) Reassemble in reverse order and Do Not Forget to reattach the small clear Water level sensing HOSE to the tub before closing the top.
13)Place Drive Belt onto the 2 small pulleys First, then slowly turn large pulley while walking belt onto it.
14)Reconnect machine to utilities and test run on small load to ensure no leaks and propper operation.
15)Enjoy Quiet free operation once again :)

Skreeching noise during spin cycle

  • Customer: Robert from Mesa AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 39 of 39 people found this instruction helpful
Pulled out washer, laid on front, removed access panel and the pump was right there. Three screws with 5/16" nut driver, pliers to release hose clamps, remove hoses, remove belt from pully, remove old pump. Install new pump with three screws, two hoses and clamps, finally put belt on new pulley and other small pulley and used screw driver shaft to pull belt on to large pulley. replace access panel, put washer back in place. It literally took me more time to clean the floor under where the washer was than to change the part. Piece-o'-cake.

broken motor pulley

  • Customer: leighton from staten island NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 39 of 48 people found this instruction helpful
i removed the plastic cover.then i disconnected the harnest.i then removed the 2 screws and took the motor out. i took a hack saw blade and made a mark in the old pulley. i then took a screw driver and put it in the crack and tapped on it and the old pulley fell apart. i then put on the new pulley and reconnect the motor. i then reconnect the belt.my washer is working great.it was so easy and i save myself some money in the process.

Water would overflow from the top of the machine

  • Customer: Peter from Manorville NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 40 of 52 people found this instruction helpful
The repair was very easy. Remove a few screws, switch wiring one at a time so I put them in the correct position and replace. The hose replacement was easy at the swicth but a little more difficult at the lower end of the tub due to limited space. Overall an easy job and now it works fine!

motor pulley burn and belt too

  • Customer: Jose A from Kissimmee FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 38 of 49 people found this instruction helpful
I pull out the motor pulley and put the new one then put belt on. but looks like the water pump its bad and I will have to order from you. Your service its the best I ever had ordering and deliver A+++++

The unit was leaking during agitation and spin cycle

  • Customer: Dan from Grain Valley MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 33 of 35 people found this instruction helpful
I had to remove the back lower panel with a nut driver (approximately 8 screws) as well as the front panel which is removed by poping the top of the unit removing 2 screws and swinging the panel down and lifting off.
Remove the bleach fill cap (pry off). You'll need a long extension on your ratchet to remove the bolt holding on the agitator. Next remove the inner tub which is held on by 4 bolts. The outer tub is a bit more difficult. You will need to remove all 4 shoulder screws from the top as well as the six that anchor it to the spring assembly around the bottom skirt. Since it was 7 years old I had to muscle the outer tub and rotate it to get around the inner tub transmission flange.
I'm not sure which of the 3 parts were leaking so I ordered and replaced all 3.
I don't know if it was necessary but I scraped and cleaned the aluminum flange plates where the gaskets seated.
At this point it was easy to replace the tub to housing gasket and tub/housing seal.
During reassembly I also replaced the basket to centerpost gasket.
I went with standard delivery but got the parts the next day.

make loud rubbing noise like a finger on wet glass

  • Customer: michael from mountain home ID
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 32 of 32 people found this instruction helpful
It auger would barely spin and the machine would squeal to a stop after the spin cycle. After reading some other posts on here, I decided that it is most likely the brake so I bought the brake repair kit.
Because the machine was old, I took the time to clean it while I was repairing the brake; thus the extra time, but it was well worth it.

1) go to hard ware store and buy 6 2" #10-24 screws; they will be required to remove and install the brake spring

2) you have to gut the machine (which is very easy) - working from the top
* unplug, drain water, and move it to an open space where you can easily work on the floor around it, and where you have a wall to support the top panel of the machine
* tilt washer on the side and remove the drive belt and pulley from the main shaft in the center
* lower washer and then remove the front panel and raise the top panel to rest against the wall/backstop
* remove the auger
* remove the white top from the tub
* remove any hoses connected to the plastic tub
* now you can push the tub to each side so that you can remove the springs - it is easier if you have someone push the tub down from the top while you remove the springs with pliers.
* remove the tub

3) remove the brake - working from the top with the tub turned upside down
* remove every other screw from the break and replace with the 2" screws
* remove the remaining original screws and replace with the 2" screws
* now, release the screws so that the brake spring is release with equal pressure on each screw
* remove the brake guts and replace with new

4) now would be a good time to clean out any mold and mildew

5) re-assembly is opposite of removal*
* the springs are more difficult to attach, and I would recommend starting with the spring in the back, by the drain and working towards the front of the washer

My machine is now quieter than when we first bought it! The brake was the problem!

03-2011

The agitator auger was broke.

  • Customer: Donna from Borger TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 36 of 50 people found this instruction helpful
All i did was remove the screw, took off broken agitator auger and replaced it with the new one and put the screw back in and was done in about 5 mintues. Super easy.

washer would agitate, pump, but not spin

  • Customer: steve from lebanon OH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 30 of 36 people found this instruction helpful
First I unplugged it, then removed the agitator and tub assemblies, then I tipped it back and removed the belt and pully and thrust bearings. After reading on here I learned the brake would stick and after installing the thrust bearing kit I found out I couldnt fit in the shims. That led me to believe the brake was siezed inplace so i couldn't fit in the parts. I removed the thrust bearing kit and removed the transmission assembley. I took apart the brake and found the two pieces had siezed together, after I got them apart I sanded both peices and lubed the shaft with high temp silicone like you would use on a cars brake system. I put the brake back together, BE VERY CAREFUL THE SPRING HAS ALOT OF PRESSURE! I then put the transmission back in, reinstalled the thrust bearing kit and it fit great. I put in the tub and agitator and washed clothes.

Water Dripping into the tub

  • Customer: William from McKinney TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 30 of 36 people found this instruction helpful
Unplugged the electrical plug from outlet. Disconnected the water hoses after I turned off the water supply. Using a screwdriver, popped up the washer top. Using needlenose pliers, I removed the wired from the defective valve, and removed the hose that feeds water into the tub. From the back of the washer, I removed th screw holding the valve in place. Reaching inside the washer, I removed the defective valve. I attached the electrical wires and hose to the new inlet valve prior to installing the valve. After installing the valve in place, I inserted the screw in the the valve from the back of the machine. I then reattached the hot and cold water hoses, closed the top of the washer, turned on the water supply, and plugged the machine back into the electrical outlet. I turnd the machine on, then off, and the water was no longer dripping into the machine. Problem fixed.

Hinge pin on one side and Lid hinge on the other

  • Customer: Jon from Ridgecrest CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 28 of 32 people found this instruction helpful
First I popped the lid up to about 70 degrees. Then removed the two hinges. Then removed and replaced the two hinge pins. The key is to then just start the two screws for the hinges, slip the pins in and then tighten the hinge screws. Total time was 5 minutes.
All Instructions for the LNC6766B71
1-15 of 374