LNC6762B71 Admiral Washer - Instructions

I know nothing about washing machines. Couldn't even find the drive from the motor to the drum until I leaned the machine backwards by chance and found the belt drive underneath. Removed belt and checked freedom of spin on motor, drum, and pump. Pump shaft was bent and frozen. Easy $75 fix saved purchase of a new machine. I had a plastic water spill tray under the washer that did not have a flat surface. This tray did not leave enough clearance for the pump wheel. I think that when the washer would sometimes rock during spin cycle, the pump wheel would hit the drip tray and that's why it eventually bent the shaft. This discovery might help others.

First I replaced the Snubber but after I tried the spin cycle, the washer still made banging noises. I removed & replaced all 6 Suspension Springs & now the washer works like a dream

My son raised the washer whilee I removed and replace the drive belt. After replacing the drive belt the loud noise when spinning is still there so don't know where the noise is coming from. The clothes after the spend cycle were normal. The video really help figure where the drive belt was located.

Following the other repair examples posted. Replaced Snubber Ring and 6 tension springs. Washer works great again. No more dancing in the hallway.

remove small panel on backside of washer, 3 screws. removed both intake and out take hoses on pump, clamps only. removed screws holding pump in place,2 i think. removed old pump replaced with new pump.attached both intake and outtake hoses with same clamps.Finished with pump installment. removed old belt by loosening the motor pully and slipping the belt off. placed new belt on pully and drum mechanism. tightened the belt to proper tension. ran a short cycle to ensure working condition then replace back panel.

Determined it was the pump through listening to where the noise came from by taking the back panel off for easy access. The pump is at the back of the unit and was easily accessable. The Motor is on a pivot bracket with springs, so it was easily moved to loosen the belt for removal. After removing the 2 drain hoses with the pliers, the pump came out with 3 screws. Replace the new pump with the reverse procedure. It worked perfectly.

Used pliers to remove spring clamps on either end of hose. Removed hose. Put clamps on end of new hose. Slipped hose ends in place and re-secured with clamps. Another save by PartSelect!

Posted instructions/videos were on the mark.
Some springs are more difficult to reach, so disconnecting the entire cabinet from the base to gain access from different angles helps a lot to connect/disconnect the springs.

Removed drive belt Removed pump access panel removed 2hose clamps 3 3/8s hex screws removed pump and reinsalled pump and belt

Watched videos on how to replace the hose. Armed with the information I started the process. But the videos were wrong. After removing a bunch of screws and not getting to the hose I removed the inspection panel on the rear,three screws and there was the hose.simple. I wished I had not watched the videos.

I remove the necessary panels, hoses and electrical section and removed the tub springs and pulled the tub assembly out of the unit and replace the snubber ring. Was really not hard to do and it worked like a charm. No more problems :)

Disconnect AC, turn off water pressure, flip it backwards to remove the drive belt below, open back small panel (4 screws), Use pliers to disconnect hoses from drain pump, and finally remove the 3 bolts, and walah, reverse procedure and tell your spouse what a hero you are.

removed the bottom back, changed the pump/pulley assembly, tilted to change the belt. Easy and fixed our problem.

First thing was to go to PartSelect website to see what others with the same problem did to solve their problem. It was 45% pump and a lot less for the belt. My belt is only a year old so that was out. I ordered my new pump and watched the video on PartSelect a couple of times. I didn't bother to disconnect the water and drain lines. I had my wife hold a plastic 2 quart container under the pump when I pulled the small hose off and didn't spill a drop. Like the man on the video said...the new pump isn't identical but it fits and works fine. Thankx PartSelect!

installed new pump, 10 min. job