Models > LNC6762B71 > Instructions

LNC6762B71 Admiral Washer - Instructions

All installation instructions for LNC6762B71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6762B71
376-390 of 476
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Major Water Leak Through Bearing Seals on Pump

  • Customer: David from Owensville MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
2 screws on each side hold the top of the washer to the front panel,I used a nutdriver to take them out . There are 2 clips on each side at the top of the washer I used a Butter Knife to push the clips in and release the front panel from the top panel ,then slid the front panel out over the bottom clips.I noticed rust in the bearings on the Drain Pump & also noticed alot of water all around the pulley and the belt,not ever having any other problems before figured that was the problem, all hoses were good and it only leaked during the drain process.There are 3 screws that hold the pump in place ,the belt for my particular model is on a swivel system around the motor and the drum just slide motor and the belt comes off,use a set of pliers to unclamp the 2 hoses attatched to the pump.To get to the belt lift washer and slide in something for the washer to rest on.Installing pum is opposite from uninstalling, Good Luck ...

Broken hinge on washer lid.

  • Customer: Bob from Girard OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Don't get unhinged by this easy repair. Easily ordered on line and got the part in two days. The only hard part was the screw was inside up under the washer body and not visible. I had to use an "s" shaped screw driver to take out and put in one screw due to the small work space.

Squeaking for a week or two on spin cycle. Finally froze up.

  • Customer: George from Fort Mill SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I know nothing about washing machines. Couldn't even find the drive from the motor to the drum until I leaned the machine backwards by chance and found the belt drive underneath. Removed belt and checked freedom of spin on motor, drum, and pump. Pump shaft was bent and frozen. Easy $75 fix saved purchase of a new machine. I had a plastic water spill tray under the washer that did not have a flat surface. This tray did not leave enough clearance for the pump wheel. I think that when the washer would sometimes rock during spin cycle, the pump wheel would hit the drip tray and that's why it eventually bent the shaft. This discovery might help others.

washer would make a loud banging noise in spin cycle

  • Customer: JOSEPH from WILKES BARRE PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I replaced the Snubber but after I tried the spin cycle, the washer still made banging noises. I removed & replaced all 6 Suspension Springs & now the washer works like a dream

loud noise when spinning

  • Customer: B and E Gifts LLC from Cedar hill TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My son raised the washer whilee I removed and replace the drive belt. After replacing the drive belt the loud noise when spinning is still there so don't know where the noise is coming from. The clothes after the spend cycle were normal. The video really help figure where the drive belt was located.

Shakes and moves on spin cycle

  • Customer: Shirley from Necedah WI
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Following the other repair examples posted. Replaced Snubber Ring and 6 tension springs. Washer works great again. No more dancing in the hallway.

very loud screeching noise when washer was rinsing/ spinning

  • Customer: SANDRA from PASADENA TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
remove small panel on backside of washer, 3 screws. removed both intake and out take hoses on pump, clamps only. removed screws holding pump in place,2 i think. removed old pump replaced with new pump.attached both intake and outtake hoses with same clamps.Finished with pump installment. removed old belt by loosening the motor pully and slipping the belt off. placed new belt on pully and drum mechanism. tightened the belt to proper tension. ran a short cycle to ensure working condition then replace back panel.

loud, grinding type noise

  • Customer: Eric from Poughkeepsie NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Determined it was the pump through listening to where the noise came from by taking the back panel off for easy access. The pump is at the back of the unit and was easily accessable. The Motor is on a pivot bracket with springs, so it was easily moved to loosen the belt for removal. After removing the 2 drain hoses with the pliers, the pump came out with 3 screws. Replace the new pump with the reverse procedure. It worked perfectly.

Water on floor under washer. Took off small back cover, squeezed hose, water dripped out. Removed hose and found split in hose.

  • Customer: David from Lexington KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Used pliers to remove spring clamps on either end of hose. Removed hose. Put clamps on end of new hose. Slipped hose ends in place and re-secured with clamps. Another save by PartSelect!

Banging, maching "walking" in spin cycle

  • Customer: Bob from Charlottesville VA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Posted instructions/videos were on the mark.
Some springs are more difficult to reach, so disconnecting the entire cabinet from the base to gain access from different angles helps a lot to connect/disconnect the springs.

Pump Pulley Striped On Shaft

  • Customer: Daniel from Potsdam NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed drive belt Removed pump access panel removed 2hose clamps 3 3/8s hex screws removed pump and reinsalled pump and belt

Drain hose leaking

  • Customer: James from Westminster CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched videos on how to replace the hose. Armed with the information I started the process. But the videos were wrong. After removing a bunch of screws and not getting to the hose I removed the inspection panel on the rear,three screws and there was the hose.simple. I wished I had not watched the videos.

Washer would shake and move when spin cycle on.

  • Customer: Mark from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I remove the necessary panels, hoses and electrical section and removed the tub springs and pulled the tub assembly out of the unit and replace the snubber ring. Was really not hard to do and it worked like a charm. No more problems :)

Loud rubbing noise and water leaks below

  • Customer: Guillermo from Rapid City SD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Disconnect AC, turn off water pressure, flip it backwards to remove the drive belt below, open back small panel (4 screws), Use pliers to disconnect hoses from drain pump, and finally remove the 3 bolts, and walah, reverse procedure and tell your spouse what a hero you are.

grinding noise

  • Customer: Cindy from Lutcher LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed the bottom back, changed the pump/pulley assembly, tilted to change the belt. Easy and fixed our problem.
All Instructions for the LNC6762B71
376-390 of 476