Models > LNC6762B71 > Instructions

LNC6762B71 Admiral Washer - Instructions

All installation instructions for LNC6762B71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6762B71
346-360 of 509
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

SEVERE VIBRATION AND MOVEMENT

  • Customer: kenneth from crystal lake IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I FOLLOWED YOUR ADVICE FOR THE PART AND WATCHED A YOU TUBE VIDEO AND IT FIXED THE PROBLEM COMPLETELY....I AM VERY HAPPY AND WILL RELAY THIS TO ALL MY FRIENDS.TAKE THE TIME TO CHECK THOROUGHLY WHAT YOU ARE DOING SINCE THE FIRST VIDEO DIDNT TELL ME THAT THERE WAS A HIGH PRESSURE SPRING UNDER THE RING THAT HELD THE SNUBBER BUT I DISCOVERED THIS BY WATCHING THE VIDEO AND IT ALL WORKED VERY WELL. THANK YOU-YOU SAVED ME $700.00.

Water leak from the bottom of the drain pump

  • Customer: Keith from Pickford MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
It was very easy. Through the access panel in the back, remove both hoses, take out three screws with 3/8ths socket, remove pump being mindful of the belt and pulley, re-set the pump with belt in place, put the three screws back in, re-connect the hoses, and done ! 10-15 minute job at the most. There will be some residual water in the pump when removed.

Machine was making really loud noises

  • Customer: Benjamin from Wylie TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Tilted the machine to remove the belt. The removed the rear access panel, disconnected the hoses and using the socket set with an extension removed the existing water pump. Put the new one in, reconnected the hoses and put the access panel back on. Much easier than I thought it would be! Now the machine is as quiet as the day we bought it!

BAd Noise & finally pump Locked up

  • Customer: Fred from Marissa IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I thought the noise was the thrust bearing. Replaced it but didn't fix. Washer worked but hstill had terrible noise. Went shopping for new washer - then pump locked up. I siphoned out the water (good idea) and folled ditections I found on this site. 1. pryed up top with screwdriver. Raised lid. 2. Removed the 2 front panel screws with a nutdriver. 3.Removed hose clamps from pump with pliers. 4. Removed 3 screws holding pump. 5.Replaced pump in reverse order. 6. Crossed fingers - it works fine - saved $800.00

Broken hinge on the lid

  • Customer: Hazel from Copley OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly like the video told me to! Seriously, I watched once when I ordered the parts, watched it again just before I started the job, and played each step as I completed that step. It simply could not have been easier. Without the video, I doubt I could have located and released the latches on the top of the washer, but seeing not only where he put the knife but the motion he used to spring them made that step so much easier than I thought it would be. With your help, I only paid a quarter of what the repairman wanted to make this simple fix -- Thank you!

water running from under the washer

  • Customer: wanda from cookeville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
new water pump

Pulley coming off of pump.

  • Customer: WILLIAM from FORNEY TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Removed old pump, disconnected hoses and drained water. Put hoses on new pump and reinstalled.

loud noise on rinse & spin cycle

  • Customer: Betsy from Van Buren Point NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed back inspection cover which was two screws,the pump with pully was right there. Removed the belt and three screws from the pully and pulled it out. Put new pully in tightened the three screws put the belt back on and the inspection cover plugged the machine back in turned it on and it ran perfect.

Burning Rubber and Metal on Metal Sound

  • Customer: Russ from Fenton MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Rubber belt was getting shredded. I replaced the motor and motor pulley (because the are one piece), but the metal on metal sound was still there. I then did some research and found out the water pump pulley could be the issue. I took it out and felt the grinding. Decided to try and tighten the screws on it, but the sounds was still there. Ordered the water pump and it was so simple to replace. (talking with my Maytag store this would have cost me over $400 to fix. With PartsSelect.com the total cost was $225.

Lid hinge was broken on the washer lid

  • Customer: max from Plymouth MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions on your video - it was very helpful! I would have never figured out how to take the top off without the video instructions. I released the top latches using the putty knife, removed the broken lid hinge & pin and installed the new ones.

Broken Lid Hinge Pin

  • Customer: Matthew from Gilbert AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took off the lid unscrewed 4 screws and replaced with new parts. Very simple.

machine would walk across floor & shake vilently

  • Customer: William from Hayesville NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Repair went as described in instructions supplied and YouTube Video "snubber ring". I could not have removed tub springs without putting 72 quarters in springs before removing as seen in another repair video which made removal and reinstallation doable. I still don't understand how this inexpensive part can cause such a problem.

Agitator stop working and water leak

  • Customer: Anthony from Fairfield CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
To simple the agitator one socket three minutes done. Water leak took longer because we had to move out the washer and took off the back with nut driver and a pair pliers done. Thank you for your incites.

Water leak into tub and inside of machine, onto floor.

  • Customer: Steven from Lompoc CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
There was a crack in the black rubber hose attached to the water inlet flume assembly, and the assembly itself was cracked and falling apart. 1) Turned off water. 2) Lifted top cover up (pry up with flat screwdriver). 3) Disconnected hose. 4) Trimmed hose above the crack. 5) Replaced "spring" -type hose clamp with small automotive-style clamp. 6) Unbolted flume from under lid (2 sheetmetal screws). 7) Reattached hose to new flume. 8) Reattached flume to underside of lid. 9) Closed lid (light pressure downward required). 10) Turned on water. Total repair time: 10 minutes.

Washing machine would get off balance with every load.

  • Customer: Brian from Camdenton MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair was very simple to do. I was worried about one post regarding the braking mechanism but had not problems with this. Once the washer was disconnected from the power and water, I moved it into a larger are for more room to work. I removed the front and back panels to disconnect the hose from the bottom of the tub to the water pump. There will be water in it so have towels ready also removed the water level hose by lifting up on top of washer. After hoses were remove, I released the belt from under the washer amd released all the springs around the bottom of the tube which was not difficult. The tube then lifted straight out the top and I set it upside down on a towel. One side I the snubber was worn completely through. With a short socket set, I loosened the screws holding in the snubber about 1/4 of the way and the snubber was easy to work out. I placed the new snubber in an tightened all the screws. Then placed the tube back into the washer. The springs were difficult to get on with the new snubber. What I did was used a small piece of this rope(about 50lbs breaking strength from Walmart) and fed fed it through the top of the washer and had the wife pull up on the spring with it while I pushed and fed it onto the proper slots. This worked well. Reconnected the hoses am put the washer back together and it works perfectly now.
All Instructions for the LNC6762B71
346-360 of 509