Models > LNC6762B71 > Instructions

LNC6762B71 Admiral Washer - Instructions

All installation instructions for LNC6762B71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6762B71
331-345 of 495
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Noise - Unit would also shut down by itself

  • Customer: Edward from Louisburg NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
At first, we ordered the drive belt, which was a little worn down. But it did not resolve the problem. Looking deeper we noticed the metal inside the water pump pulley was torn a little. So we ordered it. Received it a couple of days later, and replaced. It took about 30 mins. Now it's working like new.

The washer was not expelling water

  • Customer: Dickie from Pueblo CO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am pretty much a novice at appliance repair but am curious enough to investigate and try to save some money. I found what appeared to be the worn part but even being unsure I ordered it. It turned out it was the right part and after installing it I reassembled the washer with no spare parts left over. During a test run it was discovered that the washer drain was partially plugged. I left the drain to the professional and after that all was fine. If it ain't one thing it's three.

Washer was making a clicking sound during wash and spin cycles.

  • Customer: Theodore from Jacksonville FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Unplug the power cord and hoses. Pull washer away from the wall, tilt it backwards, reach under the washer and remove the belt.The motor has a spring loaded pulley which allows slack to roll the belt off. Turn the washer to the back is faceing you. There is a small panel with four screws in the lower left corner, take them out and remove the panel. Then you will see the drain pump. Remove the two hoses, the three screws holding the pump assembly. Remove the bad pump, and install a new one. Assemble every thing in reverse order, and sart washing.

SEVERE VIBRATION AND MOVEMENT

  • Customer: kenneth from crystal lake IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I FOLLOWED YOUR ADVICE FOR THE PART AND WATCHED A YOU TUBE VIDEO AND IT FIXED THE PROBLEM COMPLETELY....I AM VERY HAPPY AND WILL RELAY THIS TO ALL MY FRIENDS.TAKE THE TIME TO CHECK THOROUGHLY WHAT YOU ARE DOING SINCE THE FIRST VIDEO DIDNT TELL ME THAT THERE WAS A HIGH PRESSURE SPRING UNDER THE RING THAT HELD THE SNUBBER BUT I DISCOVERED THIS BY WATCHING THE VIDEO AND IT ALL WORKED VERY WELL. THANK YOU-YOU SAVED ME $700.00.

Water leak from the bottom of the drain pump

  • Customer: Keith from Pickford MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
It was very easy. Through the access panel in the back, remove both hoses, take out three screws with 3/8ths socket, remove pump being mindful of the belt and pulley, re-set the pump with belt in place, put the three screws back in, re-connect the hoses, and done ! 10-15 minute job at the most. There will be some residual water in the pump when removed.

Machine was making really loud noises

  • Customer: Benjamin from Wylie TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Tilted the machine to remove the belt. The removed the rear access panel, disconnected the hoses and using the socket set with an extension removed the existing water pump. Put the new one in, reconnected the hoses and put the access panel back on. Much easier than I thought it would be! Now the machine is as quiet as the day we bought it!

BAd Noise & finally pump Locked up

  • Customer: Fred from Marissa IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I thought the noise was the thrust bearing. Replaced it but didn't fix. Washer worked but hstill had terrible noise. Went shopping for new washer - then pump locked up. I siphoned out the water (good idea) and folled ditections I found on this site. 1. pryed up top with screwdriver. Raised lid. 2. Removed the 2 front panel screws with a nutdriver. 3.Removed hose clamps from pump with pliers. 4. Removed 3 screws holding pump. 5.Replaced pump in reverse order. 6. Crossed fingers - it works fine - saved $800.00

Broken hinge on the lid

  • Customer: Hazel from Copley OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Exactly like the video told me to! Seriously, I watched once when I ordered the parts, watched it again just before I started the job, and played each step as I completed that step. It simply could not have been easier. Without the video, I doubt I could have located and released the latches on the top of the washer, but seeing not only where he put the knife but the motion he used to spring them made that step so much easier than I thought it would be. With your help, I only paid a quarter of what the repairman wanted to make this simple fix -- Thank you!

water running from under the washer

  • Customer: wanda from cookeville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
new water pump

Pulley coming off of pump.

  • Customer: WILLIAM from FORNEY TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Removed old pump, disconnected hoses and drained water. Put hoses on new pump and reinstalled.

loud noise on rinse & spin cycle

  • Customer: Betsy from Van Buren Point NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed back inspection cover which was two screws,the pump with pully was right there. Removed the belt and three screws from the pully and pulled it out. Put new pully in tightened the three screws put the belt back on and the inspection cover plugged the machine back in turned it on and it ran perfect.

Burning Rubber and Metal on Metal Sound

  • Customer: Russ from Fenton MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Rubber belt was getting shredded. I replaced the motor and motor pulley (because the are one piece), but the metal on metal sound was still there. I then did some research and found out the water pump pulley could be the issue. I took it out and felt the grinding. Decided to try and tighten the screws on it, but the sounds was still there. Ordered the water pump and it was so simple to replace. (talking with my Maytag store this would have cost me over $400 to fix. With PartsSelect.com the total cost was $225.

Lid hinge was broken on the washer lid

  • Customer: max from Plymouth MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions on your video - it was very helpful! I would have never figured out how to take the top off without the video instructions. I released the top latches using the putty knife, removed the broken lid hinge & pin and installed the new ones.

Broken Lid Hinge Pin

  • Customer: Matthew from Gilbert AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took off the lid unscrewed 4 screws and replaced with new parts. Very simple.

machine would walk across floor & shake vilently

  • Customer: William from Hayesville NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Repair went as described in instructions supplied and YouTube Video "snubber ring". I could not have removed tub springs without putting 72 quarters in springs before removing as seen in another repair video which made removal and reinstallation doable. I still don't understand how this inexpensive part can cause such a problem.
All Instructions for the LNC6762B71
331-345 of 495