LNC6762B71 Admiral Washer - Instructions

First I disconnected the hoses and moved washer out to a larger area. Washer had to be completely torn down. Took front cover and casing off. Took all electrical and plumbing fixtures out. Removed the drum hold-down springs. Removed the drive belt. Inverted the drum/agitator section. Removed the drive pulley and bearing assembly. Removed the brake snubber. Removed the brake shoe. Reinstalled new parts. Put washer back together. It now works great.

I took out all the tubs and the apparatus holding the gear and thrust bearing assembly. I used a homemade tool (long zipties) to pull the springs off and to put them back on. After that I just replaced the thrust bearing with the new kit and put everything back together.

By sliding the machine out away from the wall I tipped it back so that it set against the wall on an angle enough for me to work on the bottom. I removed the belt and drive pully. The brake stator can be removed from the bottom if drum is centered. The brake is under pressure from a big spring in there that applies the brake. Replacing three of its mounting screws with longer ones (10-24 x 2) allows you to let pressure off of the brake spring slowly. Replaced brake rotor and stator and compressed spring with long screws as in removal. Replaced all original screws to hold in place. Installed pulley and belt. Works like brand new, all for about $30. I bought the snubber also but did not realize that this is not part of the brake. I little confusing on the parts drawing.

I tipped the washing machine back to allow me access to the bottom of the washing machine to remove the belt from the water pump. After removing the belt, I righted the machine, unscrewed the three screws holding the rear access panel on. I used pliers to remove the clamps from the inlet and outlet hoses then removed the hoses. I removed three screws holding the water pump on to the bottom panel of the washing machine. I removed the pump and replaced it with the new pump. I then reinstalled the screws, the hoses, the clamps, the access panel, and the belt. I plugged the washer back in and - viola! It works again.

I took pictures at different steps in case I forgot how it was assembled. Unplugged the power, turned off the water hoses, unplugged the hoses, pulled the washer out, took of the access panel in the lower left hand corner, took of two tec screws that hold the water valve in place, removed the four wires that were attached to the water valve, removed the water hose attached to the water valve, reattached everything to the new water valve. The only difficulty is the access panel is a bit small

The problem was not in the switch but in the plastic hose from the tub to the switch. The hose was cracked and air/water leaked which therefore didn't activate the switch. I removed the top back cover to access the switch and released the hood of the machine, like a car, using a thin scaper to depress the spring loaded retaining clips. The hose was cracked at the tub just above the retainig clip. I bought new hosing at a local hardware store and replaced the switch to omit both of them as a future problem. Sell the tube with the switch as a package deal? Damage to tube may occur from violent, out of balance, spinning tub on spin cycle.

Tried to remove brake stator with machine tilted back. Thisforced the stator off center. Removed the 6 holddown springs, water level hose and drain hose. Pull drum & transmission out of the case. Placed the drun on the ground, brake facing up. Replaced the short screws on the brake stator with 2" screws one at a time. Caution the spring has 200 lbs of force. Used 2" screws to back off spring. With spring tenshion released replace parts. Reversed proceedurer. Machine quite. Wife is happy.

I wasted time opening up the metal container for the washing machine, which was easier than expected. The top simply pops off with a little bit of prying with a screwdriver, then the front panel is held in place with two sheet metal screws. The front panel then lifts off and you can see the exterior case for the tub drive mechanism and motor. But, it wasn't obvious what was wrong until I tilted the entire unit backwards and saw the drive belt available directly under the machine and fully accessible without any tools. It was obvious, because there was a 1/8" worth of belt fragment dust under the machine. A new belt was all it needed and after I ordered it from PartSelect, I simply jimmied the old belt off the main pulley and put the new one on. It no longer squeals or slips. Hopefully, I gained another 5 years of life out of the washing machine.

Unplugged washer then took back off control panel. Removed clamp and tube from pressure switch. Pushed in tabs with a screwdriver and lifted top. Removed clamp and broken tube. Put new tube in place and tighten clamp with nutdriver. Closed top and put other end of tube on pressure switch with clamp. Put back on control panel and plugged in. Clamps are to big for application but do work. So far so good!

I could not tell where the leak was coming from. It was intermittent. Also the clothes were not getting totally dry in the spin cycle. Finally the drum stopped turning. The bearing in the waterpump was shot and the water was leaking from the waterpump. Luckily or unluckily, the bearing completely went and I then found out that the intermittent leaking was coming from the pump. I replaced the pump and the belt that was damaged when the pump bearing locked up. This has resolved the leaking issue.

First I tipped the washing machine onto its front. I removed the belt on the bottom of the machine. Then I removed the screws that held the cover in place on the back of the machine. Next I removed the two hoses that were connected to the vertical pump using pliers to pinch the clamps. I then removed three screws that held the vertical pump in place. I took the new verticle pump with pulley and mounted it to the washer and putting the washer machine back together using the previous steps in reverse order.

I took the front pannel off just 2 scrwe was holdig the pannel,the motor was in ftont,4 bolt was holdig the moto,and it is very easy to change,

Removed front cabinet, removed 6 springs holding tub down, removed pump hose, removed drive belt from motor,lifted tub out the top and placed upside down, loosened all six hex bolts(did not loosen or remove drive pulley) backed all six bolts out and left 4 threads showing, slipped old snubber out cleaned all surfaces with alchohol and slid new snubber in. Put corn starch on base where snubber rides, lifted tub back in, hooked up all six tension springs with auto brake tool. Put belt back on. . . Done. . No more beating itself to death.

found repairs on the internet. And my husband followed the repairs and the washer works wonderful thanks.

Overall, this repair should have been quite easy. The problem was removal of the old seal nut assembly. It was a bear to remove, and ultimately I had to surgically remove it from the washer in pieces. Unfortunately I broke the outer tub (plastic) in the process of getting the nut off. Once I had the silly plastic nut off, and the tub repaired the balance of the repair was absolutely easy.

My summary: This repair is really easy IF the plastic seal nut assembly comes off easily. If it doesn't budget easily, go ahead and chip it apart to get it off, being careful not to damage the threaded part of the agitator shaft. The new one will completely replace the chipped away nut.