LNC6762A77 Admiral Washer - Instructions

I had to raise the top of the washer and take off the front pannel. It was not too hard to replace the pump except that it was in the back corner and it was hard to reach the bolts to remove and install the new pump.

open top,remove back panel.then laid on the side and removed belt.remove hose from tub to pump.removed small hose for fill level.Hard part was to remove springs from tub.Then pull tub and transmission out of housing.Remove pulley from shaft.Lossen screws around snubber ring but do not remove them.Remove old snubber ring.clean surfaces with alcohol.install new snubber ring and assemble in reverse order.

1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy out,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!

took off back small metal panel, tilted washer front side down, easy to put into place after removing old part

Because I live alone, the washer is very heavy so I just used some sliding robots under the legs of washer so I could slide it out from the wall by myslef after removing the small plate in the back to accfess the water pump I used the nut driver to remove the 3 screws holding the pump in place, but I used the pliers to remove the 2 water hoses first then I mounted the water pump back into place, installed both hoses again then I tilted it back against the wall while re installing the belt then I pushed it back against the wall and removed the sliders so I could make sure it was back level this was a very easy repair even if you never fixed any thing before the belt replacement was even more simple to replace because the motor is springloaded so you just had to pull on it enough to remove it from the pulleys

Back of this washer did not remove, so we had to go in through the top--more restricting space. As you remove the old electrical metal contacts (two each of white and red), pay close attention to where they connect properly. Best to mark them so as not to confuse how to place new contacts. Also, we disconnected a white plastic hose on opposite side of top which determines load size and amount of water, so be sure to look for this.

Unbolt old pump with three bolt from top of pump inside the washer. Use needlenose pliers to remove intake and output hoses from old pump. Remove belt from pulley under washer. Reverse procedure to install. I was worried because there were two pumps listed for this model number, one being $95 and the other being $40. I bought the cheaper one and prayed. It worked just fine. Fixed a $500 washer that was on it's way to the dump and made $100 in the process!

Had wife balance washer on front edge while I accessed working parts from bottom of washer. Removed drive belt and turned agitator pulley, transmission pulley and drain pump pulley by hand. Drain pulley hard to turn and shaft had play in it. Ordered new drain pump and replaced upon receipt. Very few fasteners to remove and replace pump assembly. Drive belt was easy to remove and replace. Recommend also replacing drive belt on a washer this old.

I ordered the replacement pump assembly (water pump)for my Atlantis model maytag washer, removed the old one, installed the new one and works like a charm. The only difficulty I had was trying to figure out how to remove the cover on the front of the washer, to remove the clips, it slid side to side instead of popping out, found the instructions on-line, NO instructions came with the pump but if you have any common sense when it comes to repairs it was easy to remove and install the new part.

took drum out replase snubber put drum back in

I pulled the top ofthe washer up, I disconnected the cold and hot water hoses, took the 2 bolts off with a socket and pulled the water valve from the top. I used the pliers to take the pressure ring off and pulled over flow hose off. I pulled the four wires off with pliers. Put the new water valve in reverse order...easy.

I found on-line that replacing the snubber ring may fix the problem and ordered the part. With the instructions also downloaded I started taking the washer apart. Without the instructions the task would have been more difficult and possibly disastrous as I might have taken the bolts out that tighten down the snubber ring. All went well with a little patience. The washer works good.

got the right part great service from partselect invited my bro in law 20 mins we where done.. no more violent shaking spin cycle thank you very much

watched youtube on how to change out the snubber ring. it was quite easy.

Unplug. Open the front panel (2 clips, 2 hex head metal screws), remove the two hose clamps and hoses from the pump, remove 3 hex head screws holding the pump...bingo.. in with the new pump, hoses and panel go back....put the drive belt back on...the wife is back in buisness.. Note to all husbands out there, mess up on a few loads of laundry (mix red with white and her unmentionables turn a hideous pink) and you never have to do laundry again !!!!
Tip to all, if you have a wet-vac, attached it to the discharge hose of the washer to remove the standing water in the pump.

Right part, right price, delivered right on time Thank you Parts Select