Models > LNC6760A71 > Instructions

LNC6760A71 Admiral Washer - Instructions

All installation instructions for LNC6760A71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6760A71
46-60 of 315
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cover of washing machine wouldn't stay open, it fell on my wife's hand.

  • Customer: Edward from Coventry RI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 11 people found this instruction helpful
This is a very simple repair, I opened the top of the washer by inserting a screwdriver between the top and the washer cabinet. There are 2 clips on the front of washer, locate and push in to release top. Lift top with lid attached and remove the 2 screws holding the lid to the top of washer. Remove lid and replace hinge pin and hinge.
Replace lid, close top , all done. Total time about 15 minutes or so. Now the lid will stay up and not fall on someone.

washing machine was making alot of noise

  • Customer: David from Boca Raton FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 9 of 15 people found this instruction helpful
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again.

Machine growned when washing, brake was slipping

  • Customer: Daniel from Sugar Land TX
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 8 of 12 people found this instruction helpful
Tried to remove brake stator with machine tilted back. Thisforced the stator off center. Removed the 6 holddown springs, water level hose and drain hose. Pull drum & transmission out of the case. Placed the drun on the ground, brake facing up. Replaced the short screws on the brake stator with 2" screws one at a time. Caution the spring has 200 lbs of force. Used 2" screws to back off spring. With spring tenshion released replace parts. Reversed proceedurer. Machine quite. Wife is happy.

Plastic hinge pin broken on top cover

  • Customer: Daniel from Slatersville RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
First push inner tub to left rear, all the way, and
unscrew hinge from inside of tub. repeat same on
right side. lift cover off and unscrew other half of
hinge off cover, both sides.reverse procedures and your done.
Note: always replace both hinge's new while
you have it apart.

One of the two bolts that holds the motor in place broke off and since the bolts are actually embedded in the motor I had to buy the whole motor rather then just a 25 cent bolt.

  • Customer: Elmer from Fort Campbell KY
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 13 of 27 people found this instruction helpful
First I took the front shield off, then I took the motor off.

would'nt wash w/out getting hot

  • Customer: Emery from Talladega AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 7 of 10 people found this instruction helpful
just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go

LOW COLD WATER FLOW

  • Customer: DONALD from LENOIR NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 6 of 7 people found this instruction helpful
REPLACE VALVE BY PRYING UP THE LID IT IS MUCH EASIER THAN THE SMALL SQUARE ENTRANCE ON BACK SIDE BOTTOM

both hinges on washer lid were broken

  • Customer: Harris from Ashland PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
if you move the agiatater all the way to one side you can acess the star screws from under the hinge then push the agitator to the other side and acess the screw on the other hinge , you dont have to remove the top of the washer, let me say i did not have the serial no and the people at part select were very helpful and pacient when i called and they got me the RIGHT part the firdt time.thanks again for all your help the job came out perfect and saved me a lot of money for a repair man. ASHER

washer overflowing

  • Customer: Aaron from Lawton OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 8 people found this instruction helpful
Once the washer was unplugged, i removed the two screws on the back pannel, disconnected the three wires, rubber water line, and two screws holding it to the control panel. Quite simply reversed the process with the replacement part i ordered, which arrived overnight, and the problem was solved.

Loud squeal when spin cycle finished, white powder under washer

  • Customer: Kevin from Pooler GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 5 of 5 people found this instruction helpful
Read DIY review from William, Middleton, OH on 01-15-08. Tip on how to relieve spring pressure on brake assembly worked like a dream (3ea 10-24X2 bolts/machine screws). Replaced brake and machine works like new and was an inexpensive fix. Once the shell/housing is off the machine, tub can be turned upside down and the base doesn't need to be removed. White powder under machine was a plastic wear ring that tells you when your brake rotor needs to be changed. Brake rotor still had lining but was much thinner than replacement part. Note* Use putty knife to push in clips on front to release the top lid section.

Washer went off balance and the flume broke off

  • Customer: Michelle from Jupiter FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 18 people found this instruction helpful
I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!

Topside door would not remain in an open position; lid hinges worn out.

  • Customer: James from Oakland MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
The lid hinges are fastened to the top of the washing machine body, near the edge of the lid, with 1 screw each.
To remove the old lid hinges, with the lid clamped in the open position, I needed to gain access to the screw heads from underneath, just inside the edge of the lid opening. To get at these screw heads, I needed to push the inside wash drum toward the screw I wanted to remove and wedge something in the gap created between the body of the washer opening and the drum, directly opposite the screw that I pushed the drum towards. What? This is to hold the drum completely out of the way while getting at the screw. My wedge was the handle of a squeege that just happenned to be nearby, but just about anything will work.
Once the drum was secure, I was able to get at the screw head, which, by the way, is a totally blind operation; you cannot see the screw head, only feel it. I guess we're kind of used to feeling our way around these days. Anyway, I had to repeat the wedging thing to remove the other lid hinge.
The only real problem I had was the original (factory installed) screw heads were hex heads, and I struggled a bit finding the correct size allen wrench to blindly remove the screws. It is a good thing that I also ordered 2 new screws along with the new lid hinges because the new screws have phillips heads. Much easier to work with, even though they were a little pricey. The old hex head screws were kind of worn and it would have been a cursing operation to try to reuse them.
Once the old hinges were off, I removed the lid, installed the new hinges on the lid and clamped the lid in place in the open position, while I screwed the new hinges on (wedging the drum out of the way like before). NOTE: It might be a good idea to line the wash drum with newspaper in case a screw slips out and finds its way into one the holes in the drum; lost forever. Anyway, this may sound like alot, but it really isn't. My wife didn't even comment on how the lid isn't smashing down on her any more. That's OK, I'm grateful I'm not the one doing laundry!

shakes, noisey

  • Customer: Dan from Lafayette CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Removed the waterlines. Set the ends in a small pan or bucket to catch the water.Do the same with the drain line.
Keep an old towell handy as water will drain out of the drain pump when you remove the drain hose. Removed the back panel. Use a flat bladed screw driver to pop the top off the two clips in front holding the top down. Lift the top and pull the two screws which holds the front in place. Remove the front and set aside. Underneath, use gloves and the screw driver to remove the six springs by placing the screwdriver through the top hook end about an inch and with both hands lift the spring off. Carefull not to let the blade slip off and bust your knuckles on something,hence the gloves. Lean the machine over and walk the belt off the pulley. Disconnect the small tube in the back left corner from the drum and lift the unit out from the top. Set the drum on it's top and loosen the six screws under the big pulley just enough to pull the snubber out. Replace new snubber, tighten screws. Set drum back in place and reattach springs. Lean unit over and replace belt. Reconnect the small tube, back left corner. Replace the front panel and top. Connect the drain line and replace the rear panel. Connect waterlines and check for leaks. I went ahead and replaced all springs. I recommend replacing the belt while your at it. I'm wishing I would have. It runs like new, gets more water out on the spin cycle and the dryer dosn't take as long to dry the clothes.

MAKING NOISE DURING WASH CYCLE

  • Customer: MARK from HEBRON KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 7 of 13 people found this instruction helpful
REMOVED EXCESS WATER,REMOVED HOSES,TIPED BACK WASHER,REMOVED BELT,REMOVED PULLEY AND BEARING.REMOVED 3 SCREWS AND REPLACED WITH 3 LONGER SCREWS IN THE STATOR,THEN REMOVED 3 SHORTER SCREWS.THEN LOOSEN VERY SLOWLY EACH OF LONGER SCREWS TO RELIEVE PRESSURE FROM THE BRAKE SPRING.ONCE LOOSE,PULLED OUT BRAKE ROTOR.REPLACED WITH NEW PARTS.WORKS LIKE NEW.

Water would not shut off after filling desired level

  • Customer: Richard from Geneva OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 7 people found this instruction helpful
Took out the two top screws out that hold the top down on the back so you can lift the lid up. Removed the cover plate on the back. Take out the screw that holds the valve in place. Reach up through the access panel and undo the to clips that hold the hose and wiring. Lift the lid up and pull the unit up and remove hose and electrical connections and put back in reverse order. Very simple to do.
All Instructions for the LNC6760A71
46-60 of 315