Models > LISR310CW0WW

LISR310CW0WW General Electric Washer - Overview

Get Parts and Repair Help for LISR310CW0WW

If you know the washer repair part you need, you can browse the list of all parts on the LISR310CW0WW, or you can search by name or part description. You can also find your part by where it is located on the LISR310CW0WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LISR310CW0WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.76

Tub Dampening Strap

Appliance would take 4 straps. It is recommended to replace all 4 at the same time. They keep the tub in the center of the cabinet. Sold individually.

$3.62

D-Shaped Knob Insert Clip

Sold individually.

$5.93

Agitator Coupling Kit

Washing machine agitator drive bell with bolt. It connects the transmission drive shaft to the agitator base. *NOTE: Hold down bolt not sold separately.

$3.27

Timer Knob Clip

$10.52

Drain Hose Extension - 4 1/2' Long

$6.62

Knob and Clip

$3.00

Drain Hose Clip

This clip holds the drain hose to the back of the washer.

$37.23

Dual Action Agitator

This does not come with the fabric dispenser - must order separately or use original part.

$9.54

Tub Seal

This black new style tub seal is two and a half inches in diameter.

$8.91

Knob and Clip

This knob accepts a D-shaped shaft.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Agitator would not move during wash cycle

  • Customer: Mark from Lexington KY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 164 of 190 people found this instruction helpful
I placed both hands under the agitator 180 degrees apart, gave a quick jerk, and seperated the agitator from the coupling. With the agitator removed, use a socket and ratchet to remove the bolt holding the coupling to the spline. Remove the old coupling and slide the new one over the spline. Lightly tap on the coupling if necessary. Insert the bolt with ... read more

broken dampening strap and loose agitator

  • Customer: molly from laguna niguel CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 103 of 107 people found this instruction helpful
first remove the front washer cover by finding the two pressure clips that hold it to the top lid. gently push the putty knife into the clips one at a time. this will raise and separate them from the front panel. the panel will tilt forward and u can now remove it from the bottom clips by sliding it up and out. to open the top cover u remove the two 1/4 in s... read more

Tub seal leaked, rusted the transmission bearing which locked up

  • Customer: Wayne from Saint Augustine FL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 82 of 96 people found this instruction helpful
I followed the instructions in the GE Consumer Service Training Technician Manual Pub. No. 31-10008.

I also power washed the basket and tub before reassembly.

The tub seal comes with the transmission and brake assembly so it's not necessary to order another seal.

The agitator coupling kit contains a redesigned coup... read more