LGV7848DZ1 Whirlpool Dryer - Instructions

Unpluged the dryer. Removed the vent hose with a reg. screwdriver. used a 1/4" nut driver removed the back of the dryer. Located the The Thermal fuse and replaced it. Found the Cycling Thermostat removed the 1/4" screw and changed the wires one at a time to get them in the right spot. Reinstalled the Cycling Thermostat. Pluged the dryer in and turned it on. It fired up in about 10 seconds. Turned it off and unpluged it. Reinstalled the back and Hose and away we went.

I started by taking the front of my dryer off and cleaned it out. Next i ran the dryer and watched the flame starter circut. The starter circut would work once and then not for a long time but i could see it was tring to light because the iginiter would glow white hot. I then searched online for my model number and found the part select web site. In a few minutes I found a dryer fault description that best fit what my dryer was doing. The part select site should me three parts it might be. I read about what the three parts did on the parts select site. Then by using the process of elimination, with the knowledge I had just learned, I narrowed my suspect parts down to one. The coil for the gas valve must be the problem. So I got my ohm meter and measured the coil resistance and I found that when the coil was room temp it had resistance. But it would get hot after one heat cycle and it would open up therefore causing the gas valve not to open......no heat! I ordered the part and it came in two days!!!! All fixed!

This is a long, sad story, but I'll cut to the chase. I was told by few appliance repair guys that my problem was most likely due to the motor being bad. I had checked the thermal fuse, the door switch, and the power switch, and all were good so that made sense. I then saw a video which made it seem fairly straight forward to remove the old motor and replace it. So I ordered the motor from Part Select. Turns out it's impossible to remove the motor without also removing (and replacing) the blower. The video never mentions that. Also FYI, I found out that my dryer switch WAS broken, and nothing was wrong with the motor, so I spent $250 on a repair that should have cost %40. Oh well ...

It snapped right in. Works perfect.

I watched the You Tube video on this site. The only issue is there is a plastic fitting that I seriously damaged trying to remove the motor from the blower. You have to hold the plastic fiting stationary while turning the nut on the other end of the motor. If you try to rotate the plastic fitting you'll destroy it as I did. I got it loose by squeezing the plastic fitting with a large pair of channel lock pliers and then rotating the nut.

I was able to take apart the dryer myself and get old belt out, then my son helped me remove the drum and put new belt on. Well worth fixing; it works great again and the part with shipping and handling was only $17.00! better then price of new dryer!!!Thanks, Mary ( Cincinnati)

Initial diagnoses suspected a faulty igniter. After deterininig that there was not power to the igniter I unplugged the dryer and systematically tested the continuity of each of the temperature limit swithches which all checked OK. The last item in the circuit is the thermal fuse which proved to be faulty. To confirm that this was the only problem I monentarily by passed the fuse to verify that the burner came on. To do all this I had to remove the fron panel and take out the drum. Actually the thermal fuse is located behind th back cover and is very easy to replace and probably should have been my fist go to suspect. Note the likely cause of the thermal fuse failure is a plugged up lint filter or exhaust duct which should be checked before installing a new fuse.

Removed top, Face and pulled the tub out. Blew out all the dust and lint. Cleaned and lubed tensioner, installed new tub plastic bearing and reassembled.

looked at schematic diagram, compared to unit finally used a multimeter to check fuse.. replaced fuse, assembled dryer and turned on to check operation. OK.

Repairing my dryer was one of the easiest things I have ever done and saved me quite a lot of money. The hardest part was getting the bolts out, mainly because I used pliers instead of the tool needed for the bolts in hard to reach places. I watched a video online on how to replace the parts, ordered the parts needed for my model, and repaired it myself in minutes. I replaced the heating element, both thermostats and the Thermal Fuse. I have very little time and money invested and my dryer works perfectly.

So glad we tried the belt and rollers before going out and buying a new one. Very quiet now,so happy!

went on-line to research the problem. found the site and listed the issue. agreed with the probability and ordered the part. it came in a few days. After I ordered the part I watched the short instructional video that was available from the site. the repair took about 10 minutes to pull out the dryer, remove the back, take off the old part and put on the new part - put the back on plugged it in and push it back then turned it on. DONE

Checked motor and other components and found Thermal Fuse did not check out allowing voltage to motor. Replaced Thermal Fuse and Dryer worked

the only thing i do around the house is changing the light bulb, so when our dryer was not working and was about 5 years old, i was told it cost too much to repair and i am better of to get a new one so watched few clips on you tube and ordered the parts from partselect which came with instruction, i could not believe it spend about $100.00 and my dryer is working better than before. bottom line if i can do this anyone can.

I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.