Models > LGR3330ADB > Instructions

LGR3330ADB Admiral Range - Instructions

All installation instructions for LGR3330ADB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LGR3330ADB
31-45 of 244
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

burner head was rusted out. ordered 1 to see if part was correct. ordered 4 more to finish job.

  • Customer: Robert from Somerville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
unscrewed old burner head ;disconnected 2 wires; repaced with new burner head and replaced wires. Unfortunately, before we really needed to replace the other burner heads, the cooktop itself developed a gas leak. We decided to replace the whole thing, and therefore would like to return the unboxed, unused 4 remaining burner heads.

The burner igniter would not spark to light the burner.

  • Customer: Margie from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 10 people found this instruction helpful
I had to unscrew 4 screws on the burner unit and then 2 screws on each igniter. slip the olds out and the new ones in and then replace all the screws. And wa la they sparked and I was cooking again.

long delay before igniting - long time for oven to heat up

  • Customer: Dace from Arcata CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
The repair was easy. Partselect processed my order quickly and my part was delivered sooner than I expected.

Removing the old igniter was simple. I took off the oven door to create easy access to the oven. I then unplugged the connection and removed the screws that held the older igniter in place. Installing the new igniter was almost as easy. I followed the same steps as above, but in reverse. I accidentally dropped one of the screws, so installation probably took 1 minute longer than removal. :)

I'm a very satisfied customer.

oven wouldnt light or would light inconsistently

  • Customer: Jay from Hubbard TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 5 of 5 people found this instruction helpful
igniter would heat but oven wouldnt come on or would intermittently.opened door a little and lifted it off removed racks and bottom shield removed wingnut and burner shield,removed 2 screws holding igniter ,took off lower shield to allow access to plug,unplugged old one plugged in new one replaced shield and 2 screws holding igniter,put oven back together in reverse order,works like new :) ps if unit not unplugged from wall be careful igniter is hot with electricity and will bite you OUCH!

Broke both the left & the right side orfice tubes

  • Customer: Gerald from Cherry Valley CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set, Wrench(Adjustable)
  • 6 of 8 people found this instruction helpful
This repair is very easy. If you ever have to remove the range for any reason, for deep cleaning or otherwise, "PLEASE REMEMBER TO REMOVE THE 4 SCREWS located on the bottom of each burner! Don't do what I did! I tried to pop the range without removing the screws, & broke ALL ORIFICE TUBES! When doing this repair, shut the main gas off in the back of the oven. All you need to do is remove the 4 screws as I indicated earlier, using a Phillips screw driver, once this is done, twist off all 4 burners ("YES THEY TWIST OFF!")These twist off about 1/2 turn counter-clockwise, this will expose the electronic ignition wires connected to the ignitor electrodes, these wires are color coordinated, so remember to either write down how these wires came off, or if you are like me, just remember where they came off from, remove these "VERY CAREFULLY" as these are very delicate to remove, especially, if the ignitor electrodes are brittle or old, if they are in too bad a shape, REPLACE THEM! Once you have removed all wires connecting to the ignitor electrodes, set down the 4 burners, & the range is ready to be removed, using a flat, regular, screw driver or a small tire iron, insert the flat end into the bottom of the range, just above, where the top of the oven door is & the bottom of the range meets, the top of the oven door, the gap in-between is the spot, you want to pry, The range is held down with retainer clips, then, lift the range about half way up & remove the range. Taking a look inside, you will see the Orifice tubes & how they connect to the burner valves. Remove the two lines going to the burner valves with the use of a 1/2 wrench, or if you don't have one, a crescent wrench will do, once this is done, there is a wire restraint @ the top of the orifice assembly, please do not cut it, but turn the assembly upside down, & with your index finger & thumb, squeeze the restraint & it should pop off, then remove & replace the orifice tubes, when you are tightening the lines, only use hand-tight torque, do not over-tighten, as this will break the orifice tubes! The rest is putting the range on the oven, put the range back on the oven, reversing the procedure on taking it apart. When you put the range back on the retainer clips, you need to push down on the edge of where the clips latch in. This took me about 10-15 minutes to do. Good Luck!

When the oven was turned on, F2 and F4 came on. Oven wouldn't heat.

  • Customer: Crystal from Scott City MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.

Stove wouldn't stay lit and would fire unless the gas was turned on the range top .

  • Customer: Allen from Swengel PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 6 of 8 people found this instruction helpful
Removed the drawer and the flash plate underneath .
Unplugged the igniter then opened the & removed the over door . Lifted the bottom plate to expose the burner and igniter . Undo the 2 screws holding the igniter in place . Replace the igniter and reach underneath and plug the wire connecters together . Place all the proper things in their place .. and it was finished ...
The biggest snag I ran into was the one of the 2 screws stripped out when when taken things apart .. but I have taps and found a few new screws and replaced them ......
Quite easy fix .. don't a pay repair man to do it .... !!

F-3 error code

  • Customer: Mark from Lake Orion MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.

set oven to self clean and the inner glass broke

  • Customer: Garry from Livermore CA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

door glass broken

  • Customer: Mariano from Staten Island NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 12 people found this instruction helpful
My wife called a service company and was told that a tech would have to inspect the stove.
service charge 60.00 After inspection the parts would be orderd and a 200 fee for labor plus the parts would be charged at the completeion of the job. 2 weeks for part. I found you on the net orderd the glass. got it in 2 days and I completed the repair in 20 mins. Cost 89.00

F3 code, oven wouldn't heat.

  • Customer: Shaun from Kimball NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 9 people found this instruction helpful
First pulled the oven out and noticed how dirty the floor was underneath. Bachelors are BAD housekeepers. Next I removed the oven door (just slides off the hinges) to make it easier to reach in and unscrew the two screws holding the sensor in place in the upper left back of oven. Screws came out easily. Then I removed the back panel by removing the six screws holding it in place. I unsnapped the temp sensor wiring connection, then pulled the probe out from the front (inside the oven). Installed the new probe by feeding the wires and connector through from the front (inside the oven) and attached it with the two screws. Then went to the back again, snapped the wiring connectors together, and replaced the back panel. Then I scrubbed the floor, pushed the range back in place, reinstalled the door, and gave it a test run. PERFECTION! Heated to within five degrees of setting. EASIEST REPAIR JOB I'VE EVER DONE!

The F3 error code displayed and beeped during use of the oven and oven shut down.

  • Customer: Debra from Colts Neck NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
My husband and I began to pull the oven out and I realized that it was too heavy for me to hold. Luckily we were able to get another man to help. Other than that it was easy. Also, it took us awhile to figure out which screws secured the oven into the cabinet. We saved over $1000.00 on a new oven and installation. Kudos to everyone who added their comments! They gave us courage to give it a try.

oven would not heat up.

  • Customer: Marc from Abington PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
Remove the oven racks. Slide the two catches, located at each rear corner of the oven bottom, toward the front of the oven.

Lift the rear edge of the oven bottom slightly, then slide it back until the front edge of the oven bottom clears the oven front frame. Remove oven bottom from oven.

Pulled storage drawer out to the first stop position. Lift up front of drawer and pull to the second stop position.
Grasp sides and lift up and out.

Under storage area, I removed two screws to remove a steel plate. In the oven, I removed two screws that held on the Oven Igniter. Unplugged the Igniter under the storage area.

Plugged in the new Oven Igniter, replace the two screws that held the Oven Igniter, replace the two screws for the steel plate. Put the storage drawer back, the bottom of the oven back and the racks.

It was easier than I though it would be.

Lifted stove top broke gas lines

  • Customer: George from Big Rapids MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 5 of 7 people found this instruction helpful
Replaced gas line and orifice assembly. Had to swap orifice for the LP Gas orifice I purchased with the stove. Install and adjust took about 45 minutes to complete including clean up and test.

Glass on inside of oven door cracked

  • Customer: Tim from Athens OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.
All Instructions for the LGR3330ADB
31-45 of 244