Models > LGHS2665KF0 > Instructions

LGHS2665KF0 Frigidaire Refrigerator - Instructions

All installation instructions for LGHS2665KF0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LGHS2665KF0
76-90 of 349
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

no water to the ice maker, have water to the front water through the door.

  • Customer: ROBERT from DOWNINGTOWN PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 2 of 3 people found this instruction helpful
repair went smooth except when I was done I still had the same problem, I thought for sure the valve was bad but I guess not. don't know what it could be.

Fridge leaked water all over my kitchen

  • Customer: Craig from Eastlake OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 2 of 4 people found this instruction helpful
I watched the video and followed every step as outlined. It worked perfect, until I reconnected the supply line to my triple water valve. I used the old compression fitting and the compression nut. I should have cut the line and installed a new fitting and nut. The water on the floor the next morning reminded me of that. So back out I went and replaced the compression fitting and it has been as good as new. The ice maker took a few cycles to work again, I think it needed to fill the line with water first. But I have a huge sense of pride every time I hear water dispenced or ice dump in the freezer. Thanks for the help and encouragement!

A 2" x 4" section on the bottom of the ice container bucket broke out.

  • Customer: David from Owensboro KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Simply detached the old ice container by removing four screws and removing one screw holding the lever onto the bottom of the container. A bit of advice; make sure you note how the spring is attached to the lever before removing the screw. It took me a bit to determine how the spring activated the lever when I was reattaching it to the bottom of the container. Also, double check your order before you finalize it. I must have inadvertently hit the item twice so I received two of them. This resulted in me having to return one item and paying for extra shipping both ways. I received the part within two days of my order. It was a very fast turn-around. Also, when I realized that I received two parts and had to call to explain the situation, I found the person on the phone to be extremely helpful and courteous. She sent me information regarding how to return the product and didn't ridicule me once for my stupidity.

Rust on Front Plate and Drive Blade

  • Customer: Wayne from Westford MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 7 people found this instruction helpful
Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

One blade broke from condenser fan

  • Customer: Chris from Lockport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 7 people found this instruction helpful
The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

Part broke though normal use

  • Customer: Hugh from Berthoud CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 13 people found this instruction helpful
Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

Broken tabs

  • Customer: mark from jonesboro GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 1 of 1 people found this instruction helpful
The tabs were broken by kids it took 10 minutes to repair on all 4 tabs you have to remove the push pins completed to get the new tabs to fit right

wOULD NOT DISPENSE ICE FROM ICE TRAY

  • Customer: WILLIAM from KERRVILLE TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 10 people found this instruction helpful
DID NOT REPLACE ITEMS ORDERED BUT REPAIRED ITEM (DRIVE BLADE ) AND REINSTALED REPARED PARTS UNTIL THEY FAIL COMPLETELY. i KNOW THEY WILL IT IS JUST A MATTER OF TIME.
BUT SEEING THAT I AM 72 YEARS OLD IT WAS NOT THAT DIFFICULT TO DO THE REPAIRS, JUST LIFT UP ICE BIN AND PULL OUT, THAN TAKE IT APPART REMEMBERING HOW EACH PART FACED AND IN WHAT ORDER.
THANK YOU FOR GIVING ME THE PARTS MANUAL AND NUMBERS OFF INTERNET .
SINCERELY YOURS

Water dispenser dripping causing corrosion below tray

  • Customer: Scott from Jensen Beach FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
Replacement of the water valve repair was a snap. Only the main supply line needed to use a nut to secure the water supply. All other lines were simply cut below the pointed end of the plastic tubing line, nylon nut discarded and simply pushed in to seat with a O-ring fitting. Took no more than 10 minutes to install the new valve and test for leaks after turning water back on. This was the easiest appliance repair I have done in > 5 years, 100% success first time,

Broken shelf support stud

  • Customer: Samuel from Camden SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Use pliers to remove the broken support. Clear the remaining insert pieces with screwdriver/pliers and insert the replacement part.

Refrigerator wasn't "winterized" ..This is a summer home, the cold winter cracked the water valve

  • Customer: Jimmy from west sayville NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 1 of 1 people found this instruction helpful
I put the new unit up to the old one to see exactly how it goes, took the 2 screws holding the unt off...Took the 3 water lines off with adjustable wrench, put back exactly the same way and it worked with no leaks

Drawers wouldnt open

  • Customer: Joseph from Florence CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 1 of 1 people found this instruction helpful
Replaced wall pins pulling center pins removeing set new ones replaced drawers. Damm Kids Busted the old ones it was easy to find your web site , parts and purchasse items as this was a new one It was diffacullt to use drawers

Icemaker worked sporadically, infrequently, not at all

  • Customer: Allen from Palmer Lake CO
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 1 of 2 people found this instruction helpful
Not knowing the history of the refrigerator/freezer and observing that the icemaker would cycle (ice ejector fingers would rotate when the off/on arm was toggled), I concluded that the water valve must have some hard water scale in it which was causing it to stick. I replaced the water valve and the exact same behavior continued. By elimination, I concluded that the microswitch in the icemaker must be sticking. I removed the icemaker, used a hair blow-dryer to heat/dry out the microswitches and then a little shot of WD-40 on the mechanical arms, switches, and cams fixed it.

Broken door bin (operator error, not closing crisper draw)

  • Customer: Teresa from Ormond Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
This was as simple as it gets.
I removed broken door bin after it cracked at the bracket on refrigerator door.
Then slid new door bin in existing bracket on door.
Viola, complete and good as oringnal!
It was just as easy to order the correct part from 'partslect.com'.
Thanks,
Teresa

the bottom bin-door had broken

  • Customer: Martha from Kansas City MO
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
The only issue was inserting the bin-door properly so that it was secure and would hold jars. At first it appeared that I had either ordered or received the wrong part, because it didn't seem like it was going to fit. With peseverance and determination, I was finally successful -- I just had to hold my breath and risk flexing the plastic a bit. The good news is (1) how easy it was to use the web site and locate the proper part, and (2) how quickly the order came -- ordered on-line one day, got word later the same day that it had been shipped, and it arrived the very next day!!
All Instructions for the LGHS2665KF0
76-90 of 349