Models > LG8469W2

LG8469W2 (PLG8469W2) Amana Dryer - Overview

Get Parts and Repair Help for LG8469W2

If you know the dryer repair part you need, you can browse the list of all parts on the LG8469W2, or you can search by name or part description. You can also find your part by where it is located on the LG8469W2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for LG8469W2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$7.64

Drum Support Roller

This roller is for square-ported models and has a metallic bearing in its center. They are sold individually and most dryers use 2 rollers at the rear and it is recommended to repl...

$14.26

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil.

$13.22

Multi-Rib Belt

At 93-3/8" in length, this flat dryer drum belt has 5 ridges and is 3/8" wide.

$3.91

Drum Glide

This drum glide is sold individually. ***Please Note: these should be replaced in pairs.

$4.06

Idler Pulley Wheel with Bearing

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$4.46

Thrust Washer

$6.19

High Limit Thermal Fuse

Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when ...

$25.16

Radiant Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

$16.61

Idler Lever

The spring for this part is sold separately.

$2.70

Retaining Ring

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drum not centered , clothes getting stuck in dryer

  • Customer: Chris from Hopedale MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 462 of 461 people found this instruction helpful
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared off. I took the new d... read more

Squeeling and grinding noise

  • Customer: Steven from Holderness NH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 378 of 380 people found this instruction helpful
Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to.
Followed other people's excellent instructions. Clean out al... read more

Dryer ran but would not heat

  • Customer: Gary from Haverhill NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 169 of 191 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more