Models > LG8469L2

LG8469L2 (PLG8469L2) Amana Dryer - Overview

Get Parts and Repair Help for LG8469L2

If you know the dryer repair part you need, you can browse the list of all parts on the LG8469L2, or you can search by name or part description. You can also find your part by where it is located on the LG8469L2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for LG8469L2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$7.64

Drum Support Roller

This roller is for square-ported models and has a metallic bearing in its center. They are sold individually and most dryers use 2 rollers at the rear and it is recommended to repl...

$13.80

Multi-Rib Belt

At 93-3/8" in length, this flat dryer drum belt has 5 ridges and is 3/8" wide.

$16.53

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil.

$4.41

Drum Glide

This drum glide is sold individually. ***Please Note: these should be replaced in pairs.

$4.80

Idler Pulley Wheel with Bearing

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$5.99

High Limit Thermal Fuse

Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do need to replace it. It's letting you know that something is wrong with your dryer.

$4.46

Thrust Washer

$19.70

Idler Lever

The spring for this part is sold separately.

$10.77

Door Catch Kit

This kit comes in two pieces: the catch and the clip.

$30.24

Radiant Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Squeeling and grinding noise

  • Customer: Steven from Holderness NH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 372 of 374 people found this instruction helpful
Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to.
Followed other people's excellent instructions. Clean out al... read more

Dryer ran but would not heat

  • Customer: Gary from Haverhill NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 161 of 182 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more

Replace drive belt

  • Customer: Robert from Skokie IL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 133 of 150 people found this instruction helpful
Remove front panel, lint basket, motor mounts,exhaust hood, front drum brackets. Then slip serpentine belt around drum, pressure w/ tension idler pulley and slip around drive motor spindle. Replace all parts in reverse order (a two person job).
Vacuumed inside of dryer (full of lint.) read more