LFX25960ST LG Refrigerator - Instructions

Remove water filter and water filter holder. Removed cover on back of frig. Removed clip where water line connects to back of water filter. Took half inch wrench pushed in on water line lock to release line. Repeat at other end. Reverse steps to put on new line. Easy repair.

Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.

1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).

Turn off power, remove upper and lower drawers (may need to open upper refrigerator doors to remove large freezer bin,) remove drawer supports (upper and lower), remove rear freezer panel (trick is to loosen 4 screws on fan bumpout to get the panel to come free from the freezer side wall), test thermistor with multimeter (should have continuity or near zero resistance across 2 orange fuse wires) before cutting zip ties, cut zip ties holding Thermistor in place, remove old Thermistor, install new Thermistor, install new zip ties, replace rear freezer panel, install upper and lower drawer supports, install drawers, turn on power, should be fixed if error code doesn't return after 6 hours.

Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!

Pretty simple fix.

1) Removed the screws from lower back plate
2) Removed the screws holding the plastic water lines in place (little plastic brackets - several of them)
3) Take a picture of how the tubing and what hose goes into what part - the 5/16" hose can go into 2 different spots - I didn't do this and I had to fix this
4) Pull out the hose "tabs" that lock the clamp into place (several)
5) Push in new hose
6) Put in clamp
7) I had to remove the filter on the inside of the fridge. Remove the filter, there is one screw that comes out, then you will have access to the hose clamps
8) Repeat for all the other hoses
9) Put the plate and brackets back into place (the picture really helps on how to orient and route the 3 different tubes
10) Test the water
11) Crack open a beer for a job well done

Super easy - take a picture! It will save you time!

Turned of water to refrigerator and unplugged refrigerator. Removed the water line from refrigerator. Removed back panel. Removed mounting screw from the water valve, Unhooked wire harness from valve and removed the water line on back of valve. Reconnected wiring harness to new valve, reconnected water line on back of valve. Replaced the back panel to refrigerator and put the water line back on the new valve. Turned on water valve and checked for leaks. It's now dispensing water and ice.

An easy way to get a refrigerator out from the wall is to use a tow strap or 1/2 to 3/4 in. rope. Throw a loop behind refer while keeping both ends in your hands. Let it settle down to the lower half of unit and pull using both hands. Comes right out.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders Lay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.

The Refrigerator now runs very quite.
After watching several videos I started on mine and found that it was a bit different than any in the videos. However all but the back panel was shown and that was helpful.
The back panel was a bit difficult but a hair dryer seemed to help .
All in all it was a good choice to do it myself as it was done quicker than waiting on a repair man.

I was unable to replace the shelf (no assembly required) because I was sent the incorrect part even though I gave the model #,
serial # and exact description and measurement to the agent to whom I spoke. Even worse, I was told that I was responsible for returning the part at my expense. Rather than risking getting another incorrect part I will have a replacement plexiglass made to fit my shelf.

Took out shelf were the drawer slides are, out of the fridge.
Took a look of broken plastic slides to see how they were mounted before unsnapping them off the shelf, also compared with new slides before continuing. Unsnapped broken plastic slides by pressing the plastic clips off the shelf, pressing with my fingers, no tools used.
Installed new slides the same way old slides were. Slides have a top and bottom, so make sure to compare before unsnapping them off. When aligned, they snap right in.
Installed the shelf back in the fridge with all the items that were on it, then slid the drawer back in and VIOLA! back like new.
VERY EASY, no tools needed for my fridge, not sure for different fridges.

Have had the Sears repairman come to the house to replace this part in 5 minutes for +$100.. twice. When my dad's stopped working, ordered the part and replaced it myself for the cost of the part and shipping.
Use a screw driver to pry the right side of the switch and pull out. Best to watch a youtube video first. Takes about 5 minutes.

The replacement part came in a timely manner and snapped right into place.

Remove the crisper drawer for room to work, locate the two mounting holes at the top, front of the shelf, insert the plastic hinge pin on the outside wall side. Holding the front(cover0 in one hand, reach under the cover with your other hand, grasp the second hinge pin and move it to the insert position. Using your index finger, carefully bend the bracket arm to allow the pin to be inserted.

Compress the ends. It snaps in