Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LEQ332DS0

LEQ332DS0 Frigidaire Dryer - Overview

Get Parts and Repair Help for LEQ332DS0

If you know the dryer repair part you need, you can browse the list of all parts on the LEQ332DS0, or you can search by name or part description. You can also find your part by where it is located on the LEQ332DS0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for LEQ332DS0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.91

Rear Drum Bearing Kit

This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will...

$8.15

Drum Belt

This drum belt, often referred to as a drive belt, is used in the assembly of dryers. It goes around the drum, the idler pulley, and the motor pulley. As the armature on the motor spins, this belt is what rotates the drum and tumbles your clothes during the dry cycle. If you can hear the motor running but the drum is not moving that is a sign your belt is broken, stretched, or damaged, and can no longer grip the drum. This belt is 87 3/4 inches long, and is 1/4 inch wide. Because it is made of rubber it is common for this part to become brittle and need to be replaced. This is an authentic OEM replacement part, and it is sold individually. Remember to unplug your dryer before you begin repair work.

$20.80

Drum Glide - White

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there a...

$2.41

Drum Support Bearing

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which attaches onto the inside of the rear panel of the cabinet. You will need to remove the dryer drum before completing this repair. Although replacing the drum support bearing is a fairly easy job, you will need tools to complete it. For this repair, you will need a putty knife, a Phillips screw driver, a 5/16 nut driver and maybe a small flat blade screw driver.

$72.97

Heating Element Assembly

This dryer heating element produces heat to dry clothes and is located in the rear of a dryer. If the heater element is burned, the dryer does not heat or over heats, or clothes ar...

$9.38

Thermal Limiter - Limit 220

The dryer thermal limiter, also known as a thermal fuse, blows the fuse to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenheit, the heat cuts out. If the thermal fuse is defective, damaged, or blown up then the dryer wont start, especially since it cannot be reset. It must be replaced if the following symptoms occur: the dryer overheats, takes too long to dry clothes, or there is not enough heat in the dryer. The tools needed for this repair are, a screwdriver, putty knife and needle-nose pliers. This part is manufactured for both gas and electric dryers.

$27.63

Door Catch

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, w...

$30.25

Timer Knob

This knob accepts a D-shaped shaft.

$13.16

Lower Front Felt Seal with Adhesive

$23.66

Turn - Type Start Switch

This part is used to start the dryer once you have selected a setting on the timer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud Squeaking

  • Customer: Frank from Boyertown, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 292 of 300 people found this instruction helpful
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Acc... read more

short circuit with a brasier metal support

  • Customer: Juan Carlos from Weston, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 208 of 240 people found this instruction helpful
Disconect the dryer from the main power source.

1) Remove the two screws from the rear / upper panel (below the control panel).

2) Snap the front side using a flat head screw driver.

3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.

4) Remove the rear m... read more

Thermal Limiter opened

  • Customer: Stephen from Newnan, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 212 of 276 people found this instruction helpful
Unplugged Dryer.
Opened top of Dryer, over the drum.
Removed Thermal Limiter.
Tested the Thermal Limiter - found it was open.
Checked all vents and exhaust tube for lint build-up.
Replaced Thermal Limiter.
Closed top of dryer.
Plugged Dryer back.
Tested Dryer - it works. read more