Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LEQ2152ES0 > Instructions

LEQ2152ES0 Frigidaire Dryer - Instructions

All installation instructions for LEQ2152ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LEQ2152ES0
76-90 of 305
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Front drum guidesnubber ring was worn out

  • Customer: Alan from Emporia, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
removed the top of dryer, pulled front panel back from drum and installed snubber(Front Drum guide).

Lound noise inside dryer

  • Customer: Joseph from little Egg Harbour, NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.

My dryer wasn't drying due to a blown heating coil

  • Customer: Justin from lawrenceville, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
When it comes to repairs the only thing that I can fix are sandwiches. To say that I am a handy man is usually followed by snickers from my wife and friends... However, I was able to completley take apart my dryer, replace the heating pan and coils, put it back together and it works all by myself (my wife was standing behind me with a fire estinguisher when I plugged it in for the 1st time). I took the advice of some of the post I saw on this sight and took some before shots with my camera phone and marked the wires with tape so I knew where to return them and was able to get it all done. I was suprised at how easy it was to do and how simple a dryer really is on the inside. Ordering the part and doing it myself saved me a couple of hundred dollars easy.... this was the way to go!

Heating Element broke

  • Customer: brad from oklahoma city, OK
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 4 of 7 people found this instruction helpful
much as described earler,
1. Removed 2 screws on back at the top and 2 on the chrome vent to access the belt and pulley.
2. Disconnected spring from pulley assembly and removed belt from pulley and motor.
3. Removed top of dryer.
4. Removed control panel.
5. Removed screws from inside dryer tumbler (all of them)
6. Removed bottom kick plate.
7. Removed 2 screws from inside panel (near tumbler) and 2 screws from bottom of front panel. Removed front panel.
8. Removed tumbler housing.
9. Removed heating element cover.
10. Removed heating element pan. (wires first)
11. Removed "bearing" by lifing it up (snaps in)
12. Cleaned and regreased "bearing"
Assembled in reverse order.

female part of door clasp broke

  • Customer: Tammy from St. Peters, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
All I did was push the new part into the machine! So easy!

Loud Squealing

  • Customer: William from Hudson Falls, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.

Dryer making horrible squeaking sound when running

  • Customer: SHARON from SUMMERVILLE, SC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 2 of 2 people found this instruction helpful
I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.

dryer wouldn't heat

  • Customer: billy from millsboro, DE
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 5 people found this instruction helpful
remove top of dryer by prying with large screwdriver to snap back clips that hold it on remove two screws on both sides that hold the door . remove door then remove belt from dryer tub. (to remove belt take the back panel near floor off with screwdriver and lift pullie up that hold belt. )then lift tub upward to disconnect it from it's seat; pull it straight forward to get to the heating element.un bolt it with screwdriver and disconnect the sensor and put new heat element in

replaced broken belt

  • Customer: Shelia from Elizabethtown, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 2 of 2 people found this instruction helpful
Romoved front from dryer . Then loosened tub , slid belt on , reached in back and put belt on pulley , turned tub till belt went into place and reassembled dryer all with the help of a 3 year old and an8 year old,so in my oppinion it was one of the easiest fixes i've ever done!

Drum would not spin

  • Customer: garland from Morganton, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 5 people found this instruction helpful
After unplugging the dryer, disconnecting it from the vent, and moving into an open work area, I popped the top open with the blade of a screwdriver, disconnected the two wires that connect to the door switch, then lifted the front panel (with the door) up and away from the drum. Next, I lifted the drum out of the worn rear bearing assembly and lowered it into the dryer in order to release tension on the belt. I then removed the entire drum by carrying it forward and out of the way. I then removed the old bearing assembly, which was loose and covered with metal dust. After cleaning the area with a dry cloth to remove the old grease and metal dust, and vacuuming all the lint off *everything*, I installed the new bearing assembly with a 5/16" nut driver, being careful to position the provided ball-bearing between the plastic bearing assembly and the outer clip. The little ball-bearing is very important, as it is the drum's only path to ground, and prevents the build up of static electricity as the drums spins. I then filled the new bearing assembly with the provided grease. Everything is easy up to this point, but the difficult part for me was removing the old hub from the drum and re-attaching the new one. It is held on by three screws and they become seated very tightly. After loosening them and removing the old hub from the drum, attaching the new one prvoed difficult as well, as the screw-holes in the new hub are not threaded to fit the screws. The screws muct be forced to cut a thread as you install them, which requires a great deal of force. After installing the new hub and putting the new belt (pruchased separately) around the drum, the next step is to reinstall the drum by lifting it in through the front of the dryer and positioning the new hub over the new bearing assembly and pressing it down into place. It will gently "snap" into place as it seats. Then, on the back side of the dryer, I removed the vent panel by removing the two screws that hold it in place and positioned the new drive belt (loosely dangling around the drum) over the motor's drive wheel and behind the sring-tensioned idle arm. Then it is a simply matter to reinstall the front panel by genly lifting the drum and sliding the door opening inside it, then reseating all the little clips that hold the front panel in place. I then pressed the top back into place, reconnected the vent hose, plugged it back in and checked for operation. My fifteen year-old dryer now works like new!

dryer wouldn't tumble with normally large load - very noisy when it did tumble

  • Customer: Rebecca from Kansas City, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 6 people found this instruction helpful
I disassembled the dryer using instructions from the following website for White Westinghouse (pictures really helped)
After removing the drum, I first noticed that the grouding ball was sitting on the bottom of the dryer (along with much lint). I then saw that the bracket for bearing support cup and the bearing support cup were both worn well past use. The bracket had been worn down about 1/4" to the SE with matching wear on the bearing support cup. There was a hole in the bottom of the bearing support cup (hence the grouding ball on the floor of dryer).
I installed the new idler pulley assembly and completely vacuumed out the dryer (I didn't know lint could get so stiff!). I installed the new parts from the kit once received (and the new belt bought previously) and the dryer works great. I'm so used to the obnoxious squealing that it seems odd to be so quiet.

The internet is a magnificent thing!

Latch on dryer no longer worked

  • Customer: chris from dallas, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

Motor locked

  • Customer: Patrick from Littleton, CO
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 10 of 27 people found this instruction helpful
I determined the problem was the fan wheel and housing. I located the part on partsselect.com, Ordered it and installed the afternoon I got it in the mail. Perfect fit.

I have used partsselect before, always had great luck, great prices, always have the exact part.

dryer wouldn't heat

  • Customer: Scott from Mukwonago, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Remove rear control panel cover and remove drum belt from pulleys. remove top cover by pushing in on the 2 hold down fasteners on the front with flat head srewdriver. remove front panel by removing the 2 screws and then pop it out by lifting up. disconnect the wires at the quick connect plugs and set the front aside. lift the drum up to pop it out of the bearing housing and move forward slightly to give youself good access to the wires for the heating element and disconnect the 2 wires. remove drum the reset of the way out and do your work. Replacing the heating pan and drum bearing is pretty obvious what to do. (just a few screws). remove thermal cutoff switch from old pan and install on new pan. reinstall in reverse. no need to label wires because it doesn't matter where the wires go an a switch (justs makes and breaks a circuit) and the heater doesn't matter as long as both wires are hooked up to complete the circuit. You can't mess up the quick connectors on the door. Only my heater failed but I also replaced the drum bearing as long as I had it all apart (only another ~$20). Take the time to clean out the dust from inside the dryer, it will help the blower motor run cleaner and cooler and last longer. I bought a belt also to have on hand for replacement. I didn't replace it since my old one was good and it is real quick to replace at a later time.

Dryer stopped Heating

  • Customer: Ted from Mountain Home, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Ordered in new Element. (took apart dryer first and verified the coil on the old element was broken).

-Disconnected power
-Used flat blade screw driver and popped the top of the dryer off (two clips at front of the dryer on the door piece). Pull lid back and it will rest on its own.
-Removed two screws on the inside of the front door panel then used flat blade to pop four clips off. Lift up then out to removed door panel, drum will fall down.
-Removed small white plastic rest from front frame.
-Removed back silver vent to access motor. Pull the belt tensor away from assembly and pull belt out.
-Remove drum by grabbing belt and front of drum and forcing it up until it releases from the ball housing. Slide drum out of the front of frame/dryer.
-From here you can see the heating element. disconnect the coil wires (pull them). These are in series so it doesn't matter how they go back on. Disconnect the thermostat wires (X is negative lead).
-Removed the four screws from the back of the dryer to disengaged the element. Removed.
-Reassemble backwards.
All Instructions for the LEQ2152ES0
76-90 of 305