Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LEQ1442ES0 > Parts

LEQ1442ES0 Frigidaire Dryer - Parts

All parts for the Frigidaire Dryer LEQ1442ES0

Below is a list of all parts for the Frigidaire Dryer LEQ1442ES0 - Residential. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the LEQ1442ES0
1-14 of 91
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.91

Rear Drum Bearing Kit

This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will...

$8.15

Drum Belt

This drum belt, often referred to as a drive belt, is used in the assembly of dryers. It goes around the drum, the idler pulley, and the motor pulley. As the armature on the motor spins, this belt is what rotates the drum and tumbles your clothes during the dry cycle. If you can hear the motor running but the drum is not moving that is a sign your belt is broken, stretched, or damaged, and can no longer grip the drum. This belt is 87 3/4 inches long, and is 1/4 inch wide. Because it is made of rubber it is common for this part to become brittle and need to be replaced. This is an authentic OEM replacement part, and it is sold individually. Remember to unplug your dryer before you begin repair work.

$20.80

Drum Glide - White

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there a...

$2.41

Drum Support Bearing

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which attaches onto the inside of the rear panel of the cabinet. You will need to remove the dryer drum before completing this repair. Although replacing the drum support bearing is a fairly easy job, you will need tools to complete it. For this repair, you will need a putty knife, a Phillips screw driver, a 5/16 nut driver and maybe a small flat blade screw driver.

$72.97

Heating Element Assembly

This dryer heating element produces heat to dry clothes and is located in the rear of a dryer. If the heater element is burned, the dryer does not heat or over heats, or clothes ar...

$9.38

Thermal Limiter - Limit 220

The dryer thermal limiter, also known as a thermal fuse, blows the fuse to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenheit, the heat cuts out. If the thermal fuse is defective, damaged, or blown up then the dryer wont start, especially since it cannot be reset. It must be replaced if the following symptoms occur: the dryer overheats, takes too long to dry clothes, or there is not enough heat in the dryer. The tools needed for this repair are, a screwdriver, putty knife and needle-nose pliers. This part is manufactured for both gas and electric dryers.

$27.63

Door Catch

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, w...

$13.16

Lower Front Felt Seal with Adhesive

$11.65

Lint Filter

Located at the front of the dryer, this lint filter traps lint and debris from the exhaust air flowing out of the dryer drum. This part measures approximately 12 inches long x 7 in...

$54.36

High Limit Thermostat

This high limit thermostat is used in a dryer and monitors the temperature to make sure it does not exceed 260 degrees Fahrenheit. When your dryer temperature reaches 260 it will cut it out and only comes back when it drops by at least 70 degrees Fahrenheit. If your dryer is overheating, taking too long to dry clothes, or is not producing enough heat, replacing the thermostat could be the solution to your problem. The tools needed for this part are a Phillips screwdriver, putty knife, and needle nose pliers. Refer to the manual provided by the manufacturer for installation instructions and guidance.

$44.62

Ball Hitch

This ball hitch provides support to the drum located at the back wall of the dryer. This allows the drum to spin. The bearing may have gone bad and you might notice that the ball i...

$77.45

Blower Housing with Blower Wheel

$10.33

Bearing Bracket

This OEM drum bearing bracket holds and supports the drum bearing in your clothes dryer. The bracket is located behind the dryer drum. Common symptoms that are linked to faulty or ...

$8.61

Grounding Ball

This grounding ball is used in dryers and works to prevent friction in the rear bearing when the drum rotates. If your dryer is making a squealing, loud, banging noise or will not operate, it is best to replace it to solve the problem. To repair, first remove the main top and remove the strap at the back of the dryer to lift the lid. Next, remove the two wire harnesses and Phillip screws on the sides that connect to the front panel. Now that you have access to the inside of the dryer, refer to the manual for further instructions by following the manual provided by the manufacturer.

All Parts for the LEQ1442ES0
1-14 of 91