Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LE2812

LE2812 (P7804816W W) Amana Washer - Overview

Get Parts and Repair Help for LE2812

If you know the washer repair part you need, you can browse the list of all parts on the LE2812, or you can search by name or part description. You can also find your part by where it is located on the LE2812 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LE2812 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the LE2812

[Viewing 2 of 2]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$21.99

'M' Series New Style Coil Kit

This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils ...

$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough to ignite gas to light the burner. Once the igniter is hot enough it will open the valve and allow gas to flow. This is a safety mechanism to prevent dangerous levels of gas from building up. To repair, the main top of the dryer should be lifted, as well as the front panel to access the component. This flame sensor assembly is made of both plastic and metal.

$35.33

High Limit Thermostat

If you notice that your dryer will not start, shuts off too soon or provides too much heat, you may need to replace your high limit thermostat. This high limit thermostat acts as a...

$3.02

Screw, 8-18 x 1/2

This screw is sold individually.

$4.89

Screw

Sold individually.

$5.38

Screw

This screw is sold individually.

$3.02

Screw - 12-14 x 1/2 Type B

Sold individually.

Lock Nut

Igniter Kit

This flat style gas dryer igniter kit includes an igniter and the bracket that goes with the igniter. The glow bar silicone carbide gas dryer igniter has a ceramic tip, and is just...

Gas Valve Assembly

This valve comes with electrical solenoids/coils.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer ran but would not heat

  • Customer: Gary from Haverhill, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 311 of 348 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more

Timer wasn't working (New Timer)

  • Customer: Joaquin from Las Vegas, NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 136 of 77 people found this instruction helpful
Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I ordered the coils for ... read more

Dryer flame goes out after about 8-minutes from start and won’t work again until a 15-minute rest.

  • Customer: andy from Bethesda, MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 122 of 64 people found this instruction helpful
There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils & the problem was co... read more