Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LDEA400ACL

LDEA400ACL Admiral Dryer - Overview

Get Parts and Repair Help for LDEA400ACL

If you know the dryer repair part you need, you can browse the list of all parts on the LDEA400ACL, or you can search by name or part description. You can also find your part by where it is located on the LDEA400ACL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for LDEA400ACL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the moto...

$43.29

Heating Element Kit - 240V 4750W

This dryer heating element kit is 240 volts and 4750 watts. The kit comes with a high limit thermostat of L248-80. The function of the heating element is to produce the heat that allows you to dry your clothing during your dryer cycle. If your clothes take too long to dry, or if your dryer is not getting any heat or enough heat, you may need to replace your element. Before you begin your repair, make sure to disconnect the power from the dryer. The tools you will need for this repair include a putty knife, a quarter-inch nut driver, and a pair of needle nose pliers.

$43.08

Blower Wheel

This wheel has a deep D-shaped shaft receptacle. The spring clamp is not included with this part.

$50.03

Rear Drum Support Roller Kit

The rear dryer drum roller functions by holding the drum in place while the drum rotates on support wheels during the drying spin/tumble cycle. Included in this rear drum support roller kit are four screws, one spacer, two washers, two retaining rings, two rear rollers, and two cylinder support shafts. The drum support roller kit may need to be replaced if the dryer is noisy or will not tumble. Important note: This kit has been updated by the genuine manufacturer to have one spacer that is the thickness of two spacers. Please search by model number to get these parts separately.

$16.18

Rear Drum Support Roller

This rear drum support roller stabilizes the dryer drum and holds it in place during the drying cycle while the drum rotates on the support wheels. If your dryer is making loud squ...

$34.15

Motor Pulley

$5.81

Blower Wheel Clamp

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and p...

$18.18

Drum Felt Seal

The drum felt seal, used in dryers, allows the drum to smoothly glide with minimal friction. If any of the following symptoms occur with your dryer, replacing the felt seal can be a solution to your problem: makes noises, does not tumble, takes too long to dry, not enough heat, or no heat at all. First take off the front panel of the dryer and remove the drum. Next, unscrew the old drum support wheels by following the instructions from the manufacturer manual. To get the retaining clips on, place them in front of the wheel shaft and clamp down on the clip and shaft as you snap it in. This part can be used for both the front and rear in some models. Remember to unplug your dryer from the power source before beginning this project.

$3.00

Screw

This screw is sold individually.

$22.41

Thermal Fuse

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dry stopped heating - still had good air flow

  • Customer: Brianna from Littleton, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 173 of 198 people found this instruction helpful
I was about to purchase a new dryer because of the age of my dryer and not wanting to hire someone to fix it. After a little web research, I saw several do-it -yourself stories indicating this was a very easy repair.

This was an extremely easy repair and it save me lots of $$:
(1) Disconnected power
(2) Opened the top of the dryer
read more

broken tumbler belt

  • Customer: Michael from San Antonio, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 99 of 104 people found this instruction helpful
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall when it loses suppor... read more

Dryer would not start, no enterior light operation

  • Customer: Charles R. from Kingsland, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 70 of 82 people found this instruction helpful
I down loaded the dryer schematic and itentified items that would potentially cause the observed symptoms. Initially, I replaced the thermal fuse. After the symptoms returned after two loads, suspected the hi limit thermostat not regulating the heater element temperature. I located the thermostat using the illustrated parts list on your website and replaced... read more