Models > LD65ELY5 > Instructions

LD65ELY5 LG Dehumidifier - Instructions

All installation instructions for LD65ELY5 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dehumidifier repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LD65ELY5
1-11 of 11
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

bucket full light constantly blinking with error code 01 on the display

  • Customer: Seif from DETROIT MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrew and detached front and back panels, and inside framework holding the sheet metal to the body, after removing the sheet metal, unscrew the box enclosing the control board, use needle nose pliers to unhook the sensor module from the board and place the new sensor into the spots where the old sensor was connected (thermostat area, humidity Sensor, bucket switch, and control board). Close up the unit and your good to go.

broken roller wheels

  • Customer: MICHAEL from LEBANON PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
released broken wheels from their position using a screwdriver and secured new ones w/ a pliers.

bucket full light was blinking and dehumidifier would run for a few seconds then turn off

  • Customer: Larry from North Ridgeville OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
remove outer shell and control panel. take cover off off electrical connection box. remove old sensor from front of condensing coil along with wiring harness to temperature sensor and bucket switch and circuit board. reinstall new sensor in the reverse procedure. reinstall covers.

01 on humidity display and full tank light flashing

  • Customer: milan from chardon OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took the cover off and removed old sensor the new one plied wright in no problems anyone can do it

Flashing light to empty bucket when not the case.

  • Customer: Allen from Wentzville MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the sensor and solved the problem. I had a lot of difficulty with the case holding the circuit board,etc because no easy way to service. Seemes they could have made it easier with a removable panel. I actually cut the wires and re-attached the thermister later after routing. Did not use the other parts of the wiring.

turbo stopped spinning

  • Customer: Cheryl from Bradner OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Had to pop open the back. The back did not just unscrew and come off. It has to be pried off carefully. Took the turbo off and put the new one on.

bucket full light on and would not run

  • Customer: William from New Lexington OH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Bucket was not full! The web site said I needed the harness. I did not need the harness I need the sensor module A-13. The Sensor is not available. So I paid $22 for something I do not need. The dehumidifier still will not work because "the bucket is full", not to mention it is in parts now while I try and find a sensor for it.

Error Code "01" and Bucket Full indication

  • Customer: Roger from Bangor PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Note: The error code and bucket full indication is a result of a malfunction in the sensor assembly (p/n 6877A30013M. To replace the sensor assembly, do the following: (1) remove rear panel; 2) remove the front panel cover and remove bucket; 3) remove main cover (covers center of unit); 4) Remove cover over PC board on top right side of unit looking at it from the rear; 5)unplug sensor assembly connect on the main PC board; 6) remove clip that holds the temperature sensor on the compressor output tube ( this is a very strong clip)(also take a small piece of emery cloth and clean the output tube where the clip was attached); 7) use a tapered tool to spread the clip, just removed to, allow the temperature sensor to be removed from the clip; 8) unplug the bucket full switch connector; 9) remove the humidity sensor from the evaporator coil (just a snap-on connection; 10) remove the entire sensor assembly that was just disconnect during steps 1) thru 9) and reinstall the new assembly using the previous steps in reverse order; 11)Plug the unit in and all should be a go!

N/a

  • Customer: Scott from Wauseon OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We had no problem installing the product.

unit would not power on.

  • Customer: thomas from jamestown RI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed the front cover housing the switch circut board. Removed the defective unit and plugged in the new part. Unit now works fine.

unit said water bucket was full when it was not

  • Customer: mel from MIDDLETOWN PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
taking apart and testing switch and connections, then searching online and finding the exact problem and part needed
All Instructions for the LD65ELY5
1-11 of 11