Models > LATA400ASE

LATA400ASE Admiral Washer - Overview

Get Parts and Repair Help for LATA400ASE

If you know the washer repair part you need, you can browse the list of all parts on the LATA400ASE, or you can search by name or part description. You can also find your part by where it is located on the LATA400ASE by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LATA400ASE parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.05

Lid Hinge

This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.

Order within the next 8 hrs and your part ships today!
$4.75

Snubber Ring

Order within the next 8 hrs and your part ships today!
$63.68

Drain Pump with Pulley

This pump has 2 ports. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

Order within the next 8 hrs and your part ships today!
$8.14

Lid Hinge Pin

Order within the next 8 hrs and your part ships today!
$36.61

Transmission Pulley and Bearing Kit

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - t...

Order within the next 8 hrs and your part ships today!
$4.66

Screw

This screw is sold individually.

Order within the next 8 hrs and your part ships today!
$2.70

SCREW

This screw is sold individually.

Order within the next 8 hrs and your part ships today!
$2.70

Hose Clamp

Order within the next 8 hrs and your part ships today!
$7.00

Hose Clamp

This hose clamp is sold individually.

Order within the next 8 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 8 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washing machine was making alot of noise

  • Customer: David from Boca Raton FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 488 of 493 people found this instruction helpful
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again. read more

One of the plastic hinge pins brroke

  • Customer: Allen from North Little Rock AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 465 of 462 people found this instruction helpful
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated. read more

Load Grinding/Rubbing Noise in Rinse and Spin Cycles

  • Customer: Doug from Port Richey FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 123 of 134 people found this instruction helpful
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using a screwdriver to pry... read more