Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LATA300AAL

LATA300AAL Admiral Washer - Overview

Get Parts and Repair Help for LATA300AAL

If you know the washer repair part you need, you can browse the list of all parts on the LATA300AAL, or you can search by name or part description. You can also find your part by where it is located on the LATA300AAL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LATA300AAL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$56.03

Transmission Pulley and Bearing Kit

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - t...

Order within the next 9 hrs and your part ships today!
$98.98

Hub and Seal Kit

This kit prevents water from leaking around the drive shaft and down to the bottom of the tub.

Order within the next 9 hrs and your part ships today!
$34.73

Lower Bearing Assembly

Order within the next 9 hrs and your part ships today!
$13.74

Flume Hose Kit

Order within the next 9 hrs and your part ships today!

Plastic Outer Tub

$25.96

Tub Seal Kit with Brass Ring

This seal helps prevent any leaking around the transmission of washing machines.

Order within the next 9 hrs and your part ships today!

KNOB- SELE

$6.33

WASHER

Order within the next 9 hrs and your part ships today!
$380.63

TRANSMISSI

Order within the next 9 hrs and your part ships today!
$24.31

Knob and Indicator Skirt

Order within the next 9 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washing machine was making alot of noise

  • Customer: David from Boca Raton, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 520 of 525 people found this instruction helpful
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again. read more

Load Grinding/Rubbing Noise in Rinse and Spin Cycles

  • Customer: Doug from Port Richey, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 133 of 145 people found this instruction helpful
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using a screwdriver to pry... read more

Pump Making Horrible Noise And Brake Stuck

  • Customer: MICHAEL from PLYMOUTH, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 97 of 114 people found this instruction helpful
The pump was very easy to replace (3) screws, easy to reach with front panel off. (Less than 5 minut job. The brake assembly and thrust bearing was a little harder to do, but not bad at all. I found it best to flip the unit upside down to do the brake assembly. Replaced #10-24 x 1/2" screws with 2" long ones. Remember to do this (1) at a time, then back... read more