Models > LAT8014AAL

LAT8014AAL Maytag Washer - Overview

Get Parts and Repair Help for LAT8014AAL

If you know the washer repair part you need, you can browse the list of all parts on the LAT8014AAL, or you can search by name or part description. You can also find your part by where it is located on the LAT8014AAL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LAT8014AAL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$16.73

Drive Belt

This rubber V-style drive belt drives a washer's transmission.

$20.69

Pump Belt

This V-style pump belt is typically used with washing machines that use two belts. This belt is about 40.5" long and 3/8" wide. This pump belt helps turn the pump and to help make the washer agitate properly. It is generally positioned between the motor and the pump.

$55.14

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.

$2.70

Screw

This screw is sold individually.

$45.89

Drain Pump

This assembly uses 2 belts. Order belts if you notice wear and tear.

$23.22

Dryer Door and Washer Lid Switch Kit

This kit is simple on/off mechanism that prohibits the machine from operating when the door is open.

$3.96

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

$2.70

Screw

This screw is sold individually.

$7.08

Rubber Foot Pad

This foot pad is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers. Sold individually.

$2.70

Hose Clamp

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 256 of 264 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

washer would not start

  • Customer: Peter from Westbury NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 73 of 86 people found this instruction helpful
To see if the lid switch was the problem I first jumped it out and tried to start the washer. That was the problem. I removed the main controll so I could get to the lid switch. I made the mistake of removing the screws all the way out and the metal clip fell into the body of the washer, no problem since I was changing the drive beld anyway. I realized that ... read more

Drum would not drain and there was a banging noise when the drum spun

  • Customer: Charles from Whitman MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 51 of 51 people found this instruction helpful
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes ... read more