Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LAT8014AAE

LAT8014AAE Maytag Washer - Overview

Get Parts and Repair Help for LAT8014AAE

If you know the washer repair part you need, you can browse the list of all parts on the LAT8014AAE, or you can search by name or part description. You can also find your part by where it is located on the LAT8014AAE by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LAT8014AAE parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$24.68

Belt Kit

This kit includes both the drive belt and the pump belt which are both "V" shaped.

Order within the next 5 hrs and your part ships today!
$50.48

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.

Order within the next 5 hrs and your part ships today!
$5.15

Screw

This screw is sold individually.

Order within the next 5 hrs and your part ships today!
$6.08

Rubber Foot Pad

This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers.

Order within the next 5 hrs and your part ships today!
$20.42

Lid Switch

This two and a half inch long lid switch is used for washing machines that do not have a tub light.

Order within the next 5 hrs and your part ships today!
$19.13

Lid Check Switch

This is used to start your washer once the desired water level is reached.

Order within the next 5 hrs and your part ships today!
$82.38

Drain Pump

This assembly uses 2 belts. Order belts if you notice wear and tear.

Order within the next 5 hrs and your part ships today!
$5.15

Hose Clamp

Order within the next 5 hrs and your part ships today!
$10.35

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Order within the next 5 hrs and your part ships today!
$36.53

Lid Switch Assembly

This black lid switch assembly comes complete with a bracket, two switches, and a fuse. An open fuse might indicate that the lid switch is bad. The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.

Order within the next 5 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 417 of 427 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Drum would not drain and there was a banging noise when the drum spun

  • Customer: Charles from Whitman, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 240 of 127 people found this instruction helpful
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes ... read more

Damper pads wore-out and had metal to metal contact which caused the washer to spin out of balance.

  • Customer: Steven from Rockford, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 116 of 134 people found this instruction helpful
1: Disconnected all water and electrical connections.
2: Removed front panel.
3: Disconnected all wires leading from the control panel and removed the top of the washer.
4: Removed the springs that holds the drum down on the damper pads.
5: Flipped washer upside-down so the drum would hang from the bottom of the wash. This made it easy ... read more