Models > LAT4000AAW

LAT4000AAW Maytag Washer - Overview

Get Parts and Repair Help for LAT4000AAW

If you know the washer repair part you need, you can browse the list of all parts on the LAT4000AAW, or you can search by name or part description. You can also find your part by where it is located on the LAT4000AAW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LAT4000AAW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$12.42

Drive Belt

This rubber V-style drive belt drives a washer's transmission.

$16.64

Pump Belt

This V-style pump belt is typically used with washing machines that use two belts. This belt is about 40.5" long and 3/8" wide. This pump belt helps turn the pump and to help make the washer agitate properly. It is generally positioned between the motor and the pump.

$2.70

Screw

This screw is sold individually.

$60.14

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.

$17.13

Dryer Door and Washer Lid Switch Kit

This kit is simple on/off mechanism that prohibits the machine from operating when the door is open.

$48.61

Drain Pump

This assembly uses 2 belts. Order belts if you notice wear and tear.

$2.70

Hose Clamp

$33.45

Lid Switch Assembly

This black lid switch assembly comes complete with a bracket, two switches, and a fuse. An open fuse might indicate that the lid switch is bad. The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.

$2.70

Screw

This screw is sold individually.

$32.43

Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 305 of 315 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

washer would not start

  • Customer: Peter from Westbury NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 81 of 98 people found this instruction helpful
To see if the lid switch was the problem I first jumped it out and tried to start the washer. That was the problem. I removed the main controll so I could get to the lid switch. I made the mistake of removing the screws all the way out and the metal clip fell into the body of the washer, no problem since I was changing the drive beld anyway. I realized that ... read more

Damper pads wore-out and had metal to metal contact which caused the washer to spin out of balance.

  • Customer: Steven from Rockford MN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 76 of 89 people found this instruction helpful
1: Disconnected all water and electrical connections.
2: Removed front panel.
3: Disconnected all wires leading from the control panel and removed the top of the washer.
4: Removed the springs that holds the drum down on the damper pads.
5: Flipped washer upside-down so the drum would hang from the bottom of the wash. This made it easy ... read more