LAT3914AAM Maytag Washer - Instructions

I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.

My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came across your site. By looking at your diagrams, I determined what parts I needed and ordered them. The parts arrived in 2 days, and I installed them. There were no leaks and it cost me under $70 (a repairman would have cost at least $250). The only thing I would recommend to those in similar situations, is to purchase a spanner wrench (your site does not sell, but others do). The stem seal and hub assembly is reverse threaded (clockwise to loosen) and is difficult to remove due to tight quarters in the tub.

Well, I found the washer leaking water from the bottom a couple weeks ago. I finally got around to pulling off the front panel and ran a couple cycles to see where the water was coming from. Turns out the leak was at the plastic pump that does the draining after wash and rinse.

So I got the model number and googled online. I found Partselect and they had every part I needed. Took me 10 minutes online to find the parts for my specific washer. I couldn't believe how easy it was. Parts came in two days...and this was right before Xmas.

Anyways, changing out the pump was simple. Took 5 minutes to get it off and put the new one in. I decided to change the hoses and elbow siphon break as well while I had the thing apart as those parts were old...but still working well.

Got the washer back together and the floor is dry as a bone. Perfect repair, really easy to do. Hardest part was figuring out how to get the front panel off.

1: Disconnected all water and electrical connections.
2: Removed front panel.
3: Disconnected all wires leading from the control panel and removed the top of the washer.
4: Removed the springs that holds the drum down on the damper pads.
5: Flipped washer upside-down so the drum would hang from the bottom of the wash. This made it easy to clean the area since it was full of dirt and ground metal dust.
6: Glued new pads (per the instructions) to the cone that protrudes up from the bottom of the washer and allowed to dry.
7: Lubricated the pads with the provided grease and added additional silicon grease to insure smooth operation.
8: Replaced drive belt.
9: Flipped the washer back up-right and installed the drum springs.
10: Reconnected all wires and attached the top of the washer.
11: Reconnected all electrical and water lines and tested operation.
12: Replaced the front panel.

Washer now runs as quite and smooth as it did when it was new.

To see if the lid switch was the problem I first jumped it out and tried to start the washer. That was the problem. I removed the main controll so I could get to the lid switch. I made the mistake of removing the screws all the way out and the metal clip fell into the body of the washer, no problem since I was changing the drive beld anyway. I realized that you do not remove the screws all the way out, you just have to loosen them and then slide out the lid switch & then replace it.

First found out where the belts were by tipping the machine backwards and saw that the belts were intact but extremely loose. Ordered two belts (Drive and Pump) . Re-tipped the machine and in less than three minutes, had installed the new belts. I re-hooked the hoses to the back and the machine operated as if new.

I determined that the spin bearing was bad and decided to replace the brake too. Placed the machine on its side and then removed the rubber cap, v-belt, screw, drive lug and pulley. Then used a chain-vise grip to turn the brake off with the aid of a 3 foot long pipe extender for leverage. Blocked up the tub to align the transmission and installed the new spin bearing, brake, pulley and drive lug. Adjusted the drive lug position to contact the ccw motion of the pulley at the point when I could just feel the brake pressure. Installed the screw and rubber cap. Replaced the drive belts. Tested and all works. Halleluah!

Well the washer died and would not turn on in the middle of a wash cycle. Absolutely dead. I disconnected it from power and opened up the front panel on which all the control switches and knobs are mounted. This is removed by unscrewing 4 screws at the top of the washer.

Checked the fuse, and found blown. Replaced the fuse, closed the panel and plugged it in. Still not working. Checked the Check switches and found the Check Switch really limp. Checked with Digital Multimeter and found no continuity at either position. Unscrewed the check switch. Removal and re inspection with DMM of the check switch confirmed it was bad. Opened up the check switch and found contacts were blown.

Installed a new check switch making sure all the connecting wires go in the right places. The wiring diagram in the washer was very helpful in doing so since u dont want these wires reversed. Adjusted the plunger which operates the check switches when the lid is opened to make sure it is not over or under operating the switches. This is done by loosening the bolt holding down the check switch assembly and slidint the whole assembly forwards or backwards till the plunger has just enough push on the switches. This is done to avoid the plunger from exerting excessive pressure on the check switch and the safety switch in lid open or lid closed position. (both switches are operated by the same plunger according to the lid position)

Closed panel cover and plugged the washer in. There u go, it was alive again!

I suspected the lid switch right away. Where I went wrong was in thinking that I had to get to it from below. After going to all the trouble of removing the front panel and detaching the top panel, I discovered that it was located inside the control section at the top of the appliance. It only took a few minutes to remove four screws and gain access to the old switch assembly and swap it out with the new one. One thing to note; the new switch assembly has to be set in exactly the right place along a slotted channel in order for both contacts to be activated properly. It's not difficult to find the right spot, but you have to do it consciously.

Firstly, remove ac power from washer!
After removing the front panel of the washer (two philips screws), I loosened and removed the plastic motor cover and removed three hex head screws holding the motor. Have someone help you tilt the washer so you can remove the belts by "rolling" them off of the pullies (pump pully and motor pully). What I did was use a chemical degreaser to clean the motor base metal channel where the nylon sliders reside. After doing that and letting it dry, I removed the two old
springs. I ended up reinstalling the old springs because they were not stretched and I installed a new spring (total three) on the right side of the mount. A stiff metal rod with a hook on the end will help you install the springs. Squirt some of the included silicone lubricant on both sides of the motor mount channel and exercise the lube. Reinstall the motor and plastic cover over top of motor. Clean hands and clean belts while you have them out, reinstall belts and front cover and you're finished. My wife said it never ran better!

My washer stopped spinning, even though I could hear the motor running. I did some research and found out there was two belts, opened mine up and it was broken. I replaced the belt in five minutes, start to finish. Now it's running like new.

I replace the belts - 5 min
I tried to replace the glides...I couldn't figure out how to do that..I took out the motor and and the glide mechanism...but I could not get glide braket separate from the motor mount..so i did not do this
I replace the springs and added 1 extra sping...3 instead of 2..it worked

First I removed the screws that held the side panels on at the bottom, then I removed the screws that held the front panel on and removed the panel. I removed the agitator, loosened the retaining nut with a hammer and a punch, removed the bolts holding the tub springs, removed the bolts for the top panel and flipped it out of the way. Then I removed the clamp for the inner tub and pulled it out, then I pulled the outer tub out. Then I removed the seal and scrubbed the rust off the seal mating area, then installed the new seal and re-assembled the washer. It works perfectly now and no longer leaks and it is over 20 years old. This is the first bit of problem we have had out of this machine, the lonely Maytag repairman commercials are true.

I loosened three screws to relieve the belt tension and removed the belt from the pump drive pulley. After removing the water from the wash tub I removed the intake and output hoses from the pump. I next removed the mounting screws and removed the pump. I attached the new pump loosely and re-attached the belt. I moved the pump to tighten the belt tension and tightened the mounting screws. I re-attached the hoses, filled with water, checked for leaks and replaced the front panel.

This was a pretty simple repair. In this case, the part purchased here was not the actual problem, but had to be disturbed to fix another problem. After many years, corrosion and exhaustion of grease caused the bushing on the agitator shaft to seize, and the belts to slip. In this model machine, the bushing is accessed by first removing the agitator, which is held on by a single 1/4 inch set screw, and then removing the agitator seal, which is held in by a little spring clip on top of a washer. It's soft rubber, and you will probably need a small screwdriver or pocket knife to pry it out. In this case, the bushing was not too bad, so I was able to clean the hardened grease out and free it up with a little oil, using vise grips to rotate the agitator shaft, until the oil worked in enough.

Since seals don't like to be disturbed and reinstalled, and this one requires some prying to get out, I bought a new seal, even though the old one did not leak when I temporarily reinstalled it. There is a spring inside the seal, and it is packed with grease. The new seal comes with the spring and the grease already in it, so all that is needed is to slip it over the shaft (the top has some print embossed on it, making it easy to remember which is the top), press the washer down on top of it, and replace the spring clip.Slip the agitator back on its shaft and retighten the set screw, and you're back in business.

Run the machine, and check the area where the transmission enters the bottom of the tub. There's a little weep hole there, and if the seal leaks, you'll see water coming out there.