Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LAT3500AAQ

LAT3500AAQ Maytag Washer - Overview

Get Parts and Repair Help for LAT3500AAQ

If you know the washer repair part you need, you can browse the list of all parts on the LAT3500AAQ, or you can search by name or part description. You can also find your part by where it is located on the LAT3500AAQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LAT3500AAQ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$24.68

Belt Kit

This kit includes both the drive belt and the pump belt which are both "V" shaped.

Order within the next 6 hrs and your part ships today!
$49.51

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.

Order within the next 6 hrs and your part ships today!
$5.15

Screw

This screw is sold individually.

Order within the next 6 hrs and your part ships today!
$16.35

Timer Knob

This timer knob is not quite three inches in diameter. It is all gray in color and it is made entirely of plastic.

Order within the next 6 hrs and your part ships today!
$9.35

Rubber Foot Pad

This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers.

Order within the next 6 hrs and your part ships today!
$3.91

Centering Spring

This centering spring is nine and a half inches long. It is a metallic spring.

Order within the next 6 hrs and your part ships today!
$81.08

Drain Pump

This assembly uses 2 belts. Order belts if you notice wear and tear.

Order within the next 6 hrs and your part ships today!
$7.60

Washing Machine Lid Hinge Ball

This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plastic and is used for Maytag brand washing machines.

Order within the next 6 hrs and your part ships today!
$5.15

Hose Clamp

Order within the next 6 hrs and your part ships today!
$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 426 of 436 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Drum would not drain and there was a banging noise when the drum spun

  • Customer: Charles from Whitman, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 260 of 138 people found this instruction helpful
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes ... read more

Washer Leaking and Spin Cycle stopping frequenly

  • Customer: Dan from Mason, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 156 of 163 people found this instruction helpful
* Remove front Panel
* Remeove two screws that allow the top to hing up.
* Loosen set screw on agitator (1/4" socket)
* Remove Agitator
*Loosen spanner nut from mounting seal with hammer and punch remember to loosen, turn clockwise
* Remove Inner Tub
* Losen Mounting stem with Hammer and Punch- Remember to loosen, turn clockwis... read more