Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LA7500W

LA7500W Maytag Washer - Overview

Get Parts and Repair Help for LA7500W

If you know the washer repair part you need, you can browse the list of all parts on the LA7500W, or you can search by name or part description. You can also find your part by where it is located on the LA7500W by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LA7500W parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$35.76

Water Inlet Valve

This is a water inlet valve which is used in washing machines. The valve controls and monitors the flow of water into the washer. It has a multi-mount bracket and outlet adaptor. T...

Order within the next 10 hrs and your part ships today!
$19.42

Syphon Break Elbow Kit with Clamp

For drain hose 7/8".

Order within the next 10 hrs and your part ships today!
$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

Order within the next 10 hrs and your part ships today!
$25.98

Siphon Break Connector Kit

This plastic siphon break comes with a metallic clamp and gasket. It is used with many washing machines.

Order within the next 10 hrs and your part ships today!
$4.63

Spring Retaining Clip

This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrat...

Order within the next 10 hrs and your part ships today!
$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

Order within the next 10 hrs and your part ships today!
$5.71

Screen

Found on the water inlet valve.

Order within the next 10 hrs and your part ships today!
$2.96

Screw

Sold Individually.

Order within the next 10 hrs and your part ships today!
$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

Order within the next 10 hrs and your part ships today!
$17.97

Siphon Break Elbow

Order within the next 10 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cold water valve only opened to a trickle

  • Customer: Brian from El Cajon, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 189 of 199 people found this instruction helpful
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place. I then pulled the assembly out about 3 inches and disconnected the two wire plugs. The last step was to loosen the hose clamp on the outlet hose and pull off... read more

Cycle didn't advance

  • Customer: Glenda from Seaside, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 50 of 60 people found this instruction helpful
Placed a towel on top of the washer.

Using a flat screwdriver, carefully removed black plastic cap from inside the dial. Gently lifted and slid out the small gizmo that held the timer knob onto the front of the washer. Laid the black cap, timer knob, and small gizmo on the towel.

Using a phillips screwdriver, unscrewed the 4 screws ho... read more

Water leak noted on floor at front of washer and at sides

  • Customer: Jeff from Moorpark, CA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 45 of 52 people found this instruction helpful
Occasional noted leak became worse and I had a repair service out. Incorrect detection of outer tub seal made so cancelled them and read comments about raising the top. Did so just at start of a rinse cycle to see soapy water shoot from top of syphon break then continue to dribble out through tub empty process--this is what had cause the water to flow down... read more