Models > KUIS18NNJW6

KUIS18NNJW6 KitchenAid Ice Maker - Overview

Get Parts and Repair Help for KUIS18NNJW6

If you know the ice maker repair part you need, you can browse the list of all parts on the KUIS18NNJW6, or you can search by name or part description. You can also find your part by where it is located on the KUIS18NNJW6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. We’ve also included any installation videos we have for KUIS18NNJW6 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$15.07

Ice Machine Cleaner - 16oz

Nickel Safe Formula. NOTE: This cleaner is used for free-standing ice machines only, not those that are found in your refrigerator.

$3.56

Water Tube Kit

This tubing is 1/4'' in diameter and comes with 2 inserts. This tubing may be longer than the original, and may have to be cut.

$2.70

Screw

This screw is sold individually.

$125.91

Ice Cutter Grid Complete Assembly

Used with freestanding ice makers.

$31.02

Bin Thermostat

Used in stand-alone icemakers.

$85.18

Condensor Fan Motor Kit - 115V 60Hz

This fan motor circulates the air through the refrigerator grille and cools the compressor and condenser coils. It also helps to evaporate extra water in the drain pan. Wire harness and hardware are included.

$23.71

Ice Cutting Grid Wire

There is approximately 10'of wire. Note:2 kits are needed to replace both directions.

$198.79

Circulation Pump with Motor

Used in freestanding ice-cube makers.

$3.96

Compression Nut

$13.27

Light Switch

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lack of frequent cleaning resulted in pump failure due to buildup from hard water mineral deposists

  • Customer: Louis from Cheyenne WY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 39 of 41 people found this instruction helpful
This ice maker is really a Kitchenaid appliance.

1. Remove all ice and drain water pan by removing drain cap.
2. Disconnect waterline and unplug ice maker
3. Set icemaker on a work bench unless you like working on your knees, head down.
4. Remove flip out chute and ice scoop bracket.
5. Remove water pan by removing thumb sc... read more

Believed the condensor motor was defective and causing strange odor

  • Customer: Nicholas from Frankfort IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 28 of 33 people found this instruction helpful
First disconnected the quick release electrical connection. Then loosened the three screws that were holding the motor in the bracket. However, space is limited and even with small hands it was rather difficult as the screws were in there very tight. There are a few sharp edges on the bracket and in the surrounding area of the motor area, and nicked mysel... read more

Noisy and the Fan wasn't blowing like it should

  • Customer: William from Centreville VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 23 of 23 people found this instruction helpful
I saved my Whirlpool Refrigerator (Model ET21GKXHN00) and learned a lesson. Don’t put off cleaning the refrigerant coils underneath the refrigerator. I replaced the refrigerator about 10 years ago and began to notice that the sound of this one running had changed slightly. I remembered that’s what happened to the first one just before it died. I removed ... read more