Models > KUIS18NNJB7 > Instructions

KUIS18NNJB7 KitchenAid Ice Maker - Instructions

All installation instructions for KUIS18NNJB7 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the ice maker repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUIS18NNJB7
16-30 of 60
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The fan wouldn't run as needed. The top of the refrigerator was really hot.

  • Customer: Teresa from Moneta VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 10 people found this instruction helpful
My husband took the old motor out by taking the screws out. Then, he unplugged the fan. We searched your site for the part. With the pictures on the site, we were able to match the motor exactly. The delivery was really fast. When we received the part, he installed the fan and plugged in the power connector. We have replaced refrigerator fans before but anyone can do this with no experience. Just follow the instructions and you're all set.

Ice Maker quit making cubes, cutter wire broken

  • Customer: Kenneth from New Richmond OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
First I removed the cutter grid assembly by removing two screws. Also disconnect the wire that powers the grid. Once on the bench, simply remove the broken cutter wire. String in the new wire, starting at one end and working back and forth to the other end. Tighten the terminal screw on the first end, and then "strum" the wires, one at a times, pulling the wires taught. Pull the excess wire thru the second terminal, until all wires are taught, with equal tension. Tighten the second terminal screw, and cut off excess wire at both ends. Re-assemble cutter grid into Ice Maker.
Problem solved!

Ice maker water valve leaking

  • Customer: David from Buford GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 7 of 11 people found this instruction helpful
Disconnected both water lines and two mounting screws. Installed new water lines and water valve. No problems at all. Ordered the valve on a Monday and received it the next day. Even though i chose FedEx ground. GREAT SERVICE! I am a technical service manager and I always give credit to company's with great service. In fact, I have sent your website link to our management team to show what our website could be for our customers. Easy to find part numbers, pictures of the part being ordered and ease of use. World Class support.
Kindest regards,
Dave

broken ice cutter wire

  • Customer: Leo from Ormond Beach FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
remove tray from icemaker by removing 2 screws and disconnecting 2 electrical connectiona. Remove broken wire and restring new wire. Reinstall tray.

cutting grid wire was broken

  • Customer: Audrey from Morrow GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
removed broken wire, replaced with new wire and screwed the 6 tensions screws to tighten the grid wire.

The after market 4 yr old motor was making a wierd noise.

  • Customer: Marcus from St Petersburg FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 9 people found this instruction helpful
Removed back panel and removed the motor put new quick disconnect on and tapped the mounting holes. Removed and cleaned fan blade from old motor and put on the new motor. Mounted motor plugged it in and replaced panel.

MOTOR BEARINGS LOCKING UP

  • Customer: Joseph from North Palm Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 4 people found this instruction helpful
Removed the back panel on the refrigerator--unplugged the condenser fan motor--removed the motor--placed a small fan to cool the condenser--called Parts Select--ordered the motor--the motor arrived less than 24 hours after I ordered it--replaced the motor and rear panel on the refrigerator--probably saved more than $200.00--Very happy with Parts Select service--Plus I had a misunderstanding with my credit card and John at Parts Select was very helpful --not their fault--excellent company

Ice Maker was not making normal ice and was making noise.

  • Customer: Julie from New Braunfels TX
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 4 of 6 people found this instruction helpful
Emptied ice from bin. Drained water. Added cleaner and started clean cycle. When done, restarted ice maker. Works great now!

Broken wire on the cutting grid.

  • Customer: Jeffrey from Duluth GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
Removed the grid.
removed the existing top to bottom wire.
restrung the grid with the new wire.
Then, it cut ice just fine-better than new.
Note:
wire provided is only sufficient to rewire side to side or top to bottom, not both. If you need to do both, you'll need 2. Yes, lots of money for a few feet of wire.

Slow Ice Production

  • Customer: Lori from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
I used the cleaning solution that I purchased from you and my ice maker is now working perfectly !!!!

Thanks for the fast shipping !!

Happy Holidays !!

Cutter on Ice Maker failed and needed to be replaced

  • Customer: Thomas from Powell OH
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 2 of 6 people found this instruction helpful
I completely broke down the unit cleaning or replacing any part with rust. The replacement grid assembly (cutter) came from partselect within days of ordering. I was able reassemble the unit with the new grid assemble. Now have fresh ice. Thanks Partselect... you made this do-it-your-selfer very HAPPY! My wife cannot beleive I got the unit back together.

ice cutter grid was broken

  • Customer: harold from cleveland TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
It was easy to remove the old grid and replace it with a new one.

Failed to Run

  • Customer: Lonnie E. from Canton MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Checked Overload Start Relay With Volt Ohm Meter&Replaced Them Easy And Simple Repair

UNIT RUNNING HOT

  • Customer: BRUCE from KRUM TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
INSALLED FAN MOTOR,PROBLEM WENT AWAY. THANKS

Broken Water Nozzle at Door

  • Customer: Chris from Brentwood TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!
All Instructions for the KUIS18NNJB7
16-30 of 60