Models > KUIO18NNXS1

KUIO18NNXS1 KitchenAid Ice Maker - Overview

Get Parts and Repair Help for KUIO18NNXS1

If you know the ice maker repair part you need, you can browse the list of all parts on the KUIO18NNXS1, or you can search by name or part description. You can also find your part by where it is located on the KUIO18NNXS1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.93

Ice Machine Cleaner - 16oz

Nickel Safe Formula. NOTE: This cleaner is used for free-standing ice machines only, not those that are found in your refrigerator.

Order within the next 6 hrs and your part ships today!
$4.66

Screw

This screw is sold individually.

Order within the next 6 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 6 hrs and your part ships today!
$51.82

Recirculating Pump - 60Hz

Used with stand-alone ice cube makers.

Order within the next 6 hrs and your part ships today!
$120.90

Ice Cutter Grid Complete Assembly

Used with freestanding ice makers.

Order within the next 6 hrs and your part ships today!
$31.29

Bin Thermostat

Used in stand-alone icemakers.

Order within the next 6 hrs and your part ships today!
$23.09

Ice Cutting Grid Wire

There is approximately 10'of wire. Note:2 kits are needed to replace both directions.

$5.05

Touch-Up Paint - White

18ml

Order within the next 6 hrs and your part ships today!
$13.55

Light Switch

This part controls the light.

Order within the next 6 hrs and your part ships today!
$15.86

Drain Fastener Cap

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken light switch

  • Customer: Randy from Hays KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 29 of 46 people found this instruction helpful
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is alm... read more

was not making ice

  • Customer: Richard from North Wilkesboro NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 19 of 25 people found this instruction helpful
diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well read more

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 16 of 19 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great. read more