KUIC18NNXS2 KitchenAid Ice Maker - Instructions

The process to repair was very simple, I removed the back of the refrigerator to expose the motor area. I then removed three screws that held the condenser motor in place. once it was loose I detactched the electrical harness and removed the old motor. I then placed the new motor in place and secured it with the screws and reattached the new electrical harness that came with the new part. Once completed I reviewed it to make sure I didn't miss anything. I then replaced the cover over the motor area and enjoyed my success in repairing my own appliance with no added cost for labor, which would have been expensive I'm sure. The part purchased came with clear and consice instructions very easy to follow.

Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'

We have a side-by-side fridge/freezer and we experienced a hot center post (where doors come together) and the fridge made loud noise. Also, the (old) fan motor would start, but then quit, so our issue was the motor.

For me the repair was very easy, but for an unexperienced person it may prove to be difficult. If you must order a motor/fan, do NOT order the metal fan as a plastic fan comes with the motor. What's strange is the new motor is different than the old one, but it still mounted without any required modifications. I did NOT use the wire harness that came with the motor either as it was different too, but my old one was still good.

Check all of your parts as my fan had a cracked blade, but I used "superglue" and it's fine now.

Fridge stays cold and my wife had to lower the temperature in the fridge as she was blasted by the cold!

diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well

The procedure was straightforward. I removed the cardboard backing on the lower back of the refrigerator to expose the fan unit. I then undid the electrical harness at the fan. I then removed the three screws securing the fan motor to the metal bracket. This is the hardest part in that I had to reach through and get to the screws with my small tools. I then removed the old motor and blades and placed the new motor and blades. Again, a bit tricky trying to get the three screws mounted into the bracket...small tools and hands helps. After that I used the electrical harness supplied with the kit to plug into the new motor and I was done.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I had ice cubes within a couple of hours

Very easy to replace. Down load the Manual online for a completely operating manual. Thermistor can be tested with an Ohm Meter. Proper values are listed in operating manual.

The most difficult part of this order was identifying the part. The manual and picture for this model icemaker called the part a Ice level Sensor. No such item could be identified at Parts Select or at Kitchen Aid. After looking at item after item on the parts diagram it was determined the new name was a bin Thermostat not to be confused with the Thermistor, Ice control.
Replacement was quick and easy and took 5-10 minutes. Working fine now.

removed the clip that the motor was attached too put the new motor back on reinstalled the clip back on the fridge plugged the wire harness in and works perfect now . it was easier to remove the clip than to try to install the motor by itself its just to tight and you cant get in there

Took the two pumps tested them with 12 volt Battery. one pump didn't work. Looked up part nomber on Google and it lead me to this Co.

I removed 4 screws holding the motor mounting bracket and removed the assy from the unit. I then removed 3 screws holding the motor to the bracket. I put the fan blade on the new motor and reattached the motor to the bracket. I plugged in the wiring adapter to the motor and reinstalled the bracket in the unit with the 4 screws. Finally I attached the unit wiring connector to the motor.
It was relatively easy.

Replaced the entire unit (fan and motor). Would have rated this repair as "Really Easy", but found it a little difficult because of large hands.

Removed ice scoop and holder. Remove front cover and pump bracket. Replaced pump and replaced covers. Started up and working well.

There was a loud noise coming from the fridge - we ordered the new part it came a lot sooner than we excepted and we replaced it in about 20 minutes- the hardest part was my husband getting his hand in there to put the screws in- but a very easy fix.