Models > KUIC18NNTS0 > Instructions

KUIC18NNTS0 KitchenAid Ice Maker - Instructions

All installation instructions for KUIC18NNTS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the ice maker repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUIC18NNTS0
31-45 of 88
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door handle scratch

  • Customer: Jeff from Sherwood OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
replaced handle

range handle fell off and screw got lost

  • Customer: Frances from palm beach gardens FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

Condenser motor was making noise.

  • Customer: Joe from Spring Hill TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 2 people found this instruction helpful
Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.

Cutter on Ice Maker failed and needed to be replaced

  • Customer: Thomas from Powell OH
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 1 of 5 people found this instruction helpful
I completely broke down the unit cleaning or replacing any part with rust. The replacement grid assembly (cutter) came from partselect within days of ordering. I was able reassemble the unit with the new grid assemble. Now have fresh ice. Thanks Partselect... you made this do-it-your-selfer very HAPPY! My wife cannot beleive I got the unit back together.

Freeze ruptured inlet valve

  • Customer: Lindey from Austin TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 18 people found this instruction helpful
Simple to replace. Next fall I will be sure to drain the outdoor icemake and shut it down for the winter.

leaking water inlet valve

  • Customer: Barton from Ringgold GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 2 of 9 people found this instruction helpful
Received replacement valve ~ 3 days, easily replaced in less than 15min, works great

water inlet valve was leaking and damaged the circuit

  • Customer: Hugohug from LAREDO TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 12 people found this instruction helpful
just replaced the water inlet valve, it took less than 10 minutes. Ordering the part was just as simple, no hassle what so ever. Got the part as promised and installed it in minutes just as it was explained. I will come back to this site in a hart-beat.

Thanks

water leaking from water control board.

  • Customer: otis from frenchburg KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 6 people found this instruction helpful
After turning off water to icemaker, defective control removed (two screws) and new unit installed.Worked perfectly.I was totally amazed when I ordered the part thursday afternoon and it arrived fridaY morning.Total time out of operation less than 24 hours.Wonderful results.

Fan became noisy and started wobbling.

  • Customer: James from Cave Creek AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the screws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.

Condenser Fan was making noise

  • Customer: Kerry from Franklin TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Having read a few of the user reports like this one gave me the confidence to do this repair. The space was really tight, but one of the write ups suggested removing the frame and then replacing the motor on the frame. That was an excellent suggestion. The only difficulty I had was when I used the motor screws from the old motor to install the new motor. They were slightly longer and didn't tighten down all the way. So the first "test" resulted in still having a noisy fan motor because it was shaking around a bit. But, taking it back out and using the screws that came with the new motor did the trick. The refrigerator is now whisper quiet all the time. I also appreciated the conversion wiring harness in the kit that was simply plug and play for this new motor to my old refrigerator.

Condenser fan vibrated loudly while turning

  • Customer: Robert from Aurora IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled the back panel covering the fan and condenser off the refrigerator (just a few screws) and disconnected the fan which was a simple plug. The fan was held in place with three screws which I took out. I pulled out the old fan and replaced it with the new one, three screws to secure it in place and reconnect the fan plug. Then simply replace the back panel and plug the frig in. the fan silently started right up. Good as new and no service call! :)

noise coming from back of refrigerator. determined it was the fan

  • Customer: BRUCE from SOUTH WINDSOR CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug regrigerator power cordfrom wall outlet. Using nut driver remove cover from lower back side of refrigerator. Unplug wire connection to fan. Using nut driver remove the four screws holding the fan/bracket assembly. Carefully remove fan/bracket assembly from refrigerator. Using nut driver,remove the old fan from fan bracket. Using nut driver install new fan on fan bracket. Carfefully install new fan/bracket assembly and install the four screws. Plug wire connection to fan (you may need to use adapter supplied with new fan). Reinstall refrigerator lower back cover. Plug refrigerator power cord back into outlet. Note: you may wish to carefully vacuum dust from back of refrigerator before installing back cover. You should also vacuum dust from front side.

Old fan housing broke

  • Customer: Michael from Pinedale WY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Disconnected power cord, removed rear cover of refrigerator, disconnected pig tail, removed 4 housing screws, took three mount screws out and removed old fan. Reversed steps, plugged in and complete repair done.

ice cutter grid was broken

  • Customer: harold from cleveland TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
It was easy to remove the old grid and replace it with a new one.

WATER WAS LEAKING INTO THE CONTROL BOARD

  • Customer: Alfred from Hot Springs AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I REMOVED THE INSPECTION COVER, REMOVED 2 SCREWS HOLDING THE CONTROL VALVE,DEPRESSED THE REALEASE RINGS ON THE WATER LINES,UNPLUGED THE 2 ELECTRICAL CONNECTIONS AND REMOVED THE BAD VALVE. I RE-INSTALLED THE WATER LINES INTO THE NEW PART, RECONNECTED THE ELECTRICAL PLUGS,REPLACED THE 2 SCREWS IN THE NEW VALVE KEEPER AND REPLACED THE INSPECTION COVER. EVERYTHING I RECEIVED FROM PARTSELECT FIT PERFECTLY. THANK YOU PARTSELECT, THE ICE MACHINE WORKS GREAT. I SURE WAS GLAD YOU WERE THERE. THANKS,, ALFRED HARVEY
All Instructions for the KUIC18NNTS0
31-45 of 88