Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUIA15NLHS6

KUIA15NLHS6 KitchenAid Ice Maker - Overview

Get Parts and Repair Help for KUIA15NLHS6

If you know the ice maker repair part you need, you can browse the list of all parts on the KUIA15NLHS6, or you can search by name or part description. You can also find your part by where it is located on the KUIA15NLHS6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$126.78

Ice Cutter Grid Complete Assembly

Used with freestanding ice makers.

$5.15

Screw

Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an appliance to ensure an electrical connection is not lost.

$197.17

Circulation Pump with Motor

Used in freestanding ice-cube makers.

$14.98

Switch, Plunger Grid/Light

This part controls the light.

$34.95

Ice Cutting Grid Wire

There is approximately 10'of wire. Note:2 kits are needed to replace both directions.

$90.89

Condenser Fan Motor

NOTE: As per the manufacture the part does not come threaded. A self tapping screw will need to be used to make threads.

$5.04

Compression Nut

This compression nut is used with the plastic water line of the icemaker assembly.

$16.74

Drain Fastener Cap

$2.76

Screw 8-18 x 5/8

Screw size is 8-18 x 5/8". Used with stand-alone ice cube makers.

$7.60

Screw

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lack of frequent cleaning resulted in pump failure due to buildup from hard water mineral deposists

  • Customer: Louis from Cheyenne, WY
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 61 of 63 people found this instruction helpful
This ice maker is really a Kitchenaid appliance.

1. Remove all ice and drain water pan by removing drain cap.
2. Disconnect waterline and unplug ice maker
3. Set icemaker on a work bench unless you like working on your knees, head down.
4. Remove flip out chute and ice scoop bracket.
5. Remove water pan by removing thumb sc... read more

Believed the condensor motor was defective and causing strange odor

  • Customer: Nicholas from Frankfort, IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 36 of 41 people found this instruction helpful
First disconnected the quick release electrical connection. Then loosened the three screws that were holding the motor in the bracket. However, space is limited and even with small hands it was rather difficult as the screws were in there very tight. There are a few sharp edges on the bracket and in the surrounding area of the motor area, and nicked mysel... read more

Broken light switch

  • Customer: Randy from Hays, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 46 of 74 people found this instruction helpful
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is alm... read more