KUDY25SHWH1 KitchenAid Dishwasher - Instructions

Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.

unscrewed sprayarm, removed bearing and seal, used PartSelect pic and description schematic to identify part numbers then placed order. Parts arrived in two or three days.

Removed upper basket and installed the arm. New snap in didn't require phillips screwdriver as old one and new support had split to insert. Replacing upper spray spinner dropped screw down around pump. This caused misery unassembling lower covers to receive Stainless
Steel, so magnet won't help ended up with mirror and hemistat to reach through large screen figures. So make sure to put towel or something in the bottom to catch parts.

First remove front panel of dishwasher. Held on by 2 screws on bottom of panel. Remove the electrical connections from the dispenser. Remove the six screws on the dispenser and remove dispenser. Reverse steps to install new dispenser. Also remove rinse aid sensor from old dispenser and install in the new dispenser.

I first removed the old part. when i removed the old part i could not get the conector piece off when i when to get a new one they told me i should replace the copper tubing with the more flexable tubing because the copper tubing can kink up and possibly break from the kinking. so i screwed the inlet valve on i put teflon tape on the all the threads of the conector piece screwed it into the new inlet valve with and adjustable wrench then i conected the new tubing, and tightend it down with the wrench i slowly turned the water back on to cheak for leaks. When i saw there were no leaks i turned the water on the rest of the way pushed the dishwasher back in and screwed it into place an i was done.

Removed inside cover and inserted new handle on two tabs and attached latch. Slightly tricky to get 3 pieces in place and reattach cover without them moving.

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

This was my third attempt at fixing the problem. First I tried the bushing under the lower spray arm. This worked for me a few years ago but not this time. I then replaced the door gasket with no luck. I just discovered another bushing that has worn paper thin between the lower spray arm and the nut that holds it. I ordered it and hopefully that will do the trick. I read that if the spray arm wobbles it creates waves in the tub that slop over the edge.

I was hesitant at buying the Matag made replacement, especially since it was one piece as compared to my 10-year old 3 piece assembly, and my dishwasher is KitchenAid.
Ordered on a Sunday afternoon, had in hand Tuesday same week, one phillips head screwdriver to remove/replace. Everyone smiling!
Did not need to remove upper rack. Simply unscrewed 1 screw, put on new one-piece arm, replaced with same screw.
15 minutes!
Good price/delivery.

first I removed lower basket. then removed lower sprayer attached to pump housing by unscrewing the cap by hand. the I removed the pump cover . there were six alan screw two of them were missing causing the failure of the seal spraying solution at the door. replaced the pumpseal working backwards until everthing was replaced.

Pretty simple. Hardest part was working the end clips of the slide to remove top rack. You simply need to squeeze the plastic clip in to slide it out. Once the top rack is out, it was an obvious philips head screw removal and new part replacement.

Removed the rest of the broken retainer plug. Part number was on the top of the plug. Went to Partselect.com looked up the part and ordered it. The right part (important) arrived in a few days. I put the arm back in place, screwed in the new retainer plug and we were back in business. Cost of part about $5.00. Price of not having to share in cleaning the dishes, priceless. Any future problems with any of my appliances, this is the first place I'll look for the needed part.

1-remove upper rack by removing holding clips.

2-remove old assembly from Rack

3-cut old ring guide to accomodate new style (one solid plastic piece) and reglue after accomodating new assembly

4-re-install upper rack

DONE

Removed one screw to get the spray arm off the rack, one other screw to disassembly the spray arm assembly. Replaced worn and damaged parts. Installation was reverse order of disassembly.

Pulled off the old valve using a crescent wrench and screw driver. The replacement part was a 100% exact match. Slapped on the new valve and that baby was water tight. $50 on a new valve is a lot better than $500 for a new washer.

Partselect.com was so easy to use and find the right part. Way more helpful than whirlpool's site, but that's not surprising seeing as they have an "authorized repair technician" page.

Thanks Partselect.com!