Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUDX03FTSS0

KUDX03FTSS0 KitchenAid Dishwasher - Overview

Get Parts and Repair Help for KUDX03FTSS0

If you know the dishwasher repair part you need, you can browse the list of all parts on the KUDX03FTSS0, or you can search by name or part description. You can also find your part by where it is located on the KUDX03FTSS0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for KUDX03FTSS0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.53

Door Balance Link Kit

This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwashe...

$17.21

Upper Dishrack Wheel Mount

This part is located on the top dishrack with two per side. Sold individually.

$46.26

Silverware Basket

This is a basket for washing flatware or silverware in your dishwasher.

$17.71

Chopper Assembly

This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.

$6.12

Rack Track Stop

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes ...

$11.43

Mounting Bracket

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

$19.54

Bi-Metal Fuse

This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit i...

$26.28

Tine Row

The tine row on your dishwasher rack divides the rack into columns to keep your kitchen items in place during the washing cycle. If you notice that one or more of the tines on your current tine row is damaged, you should consider replacing it. This product is made of gray plastic and is approximately 21 inches in length. This tine row contains 11 straight tines and 1 curved tine. This product is sold individually. Many of our customers have rated this repair as very easy. To complete this repair, simply remove the old tine row and replace it with the new one.

$15.03

Spinner Kit

This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.

$51.16

Water Inlet Valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced Hinge Link

  • Customer: Scott from Fort Lauderdale, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 532 of 546 people found this instruction helpful
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. read more

Worn dishrack wheel mount

  • Customer: Jason from Todd, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 513 of 523 people found this instruction helpful
This wheel mount broke from normal use and made the upper dish rack disconnect from the sliding arm that extends it outside the dishwasher body so that you can fill it. The part was delivered quickly and was easy to install using just a screwdriver to loosen the retainer clip on the end of the extension slide. Once the retainer clip was removed, the new part... read more

The wheel mount had broken so that the wheel was disconnected from the mount on the upper rack, making the rack unstable.

  • Customer: Elizabeth from San Francisco, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 381 of 390 people found this instruction helpful
I had to fiddle with the mount a bit to get it on the rack properly. Then I pulled back slightly on the inner part of the end piece of the track while also pulling the top of the piece back and released the inner tip of the piece, allowing the end piece to be removed. I placed the new wheel in the track and replaced the end piece.

Super easy and... read more